TFF22DWB General Electric Refrigerator - Instructions

Removed the broken fan blade (just pulled off) and replaced with part purchased PartSelect. Very easy repair, no tools required.

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Laying on the floor I blocked up the door. Removed old hinge and cam. First I replaced the cam then I inserted the hinge into the cam. Positioned the door to enable me to refasten the hinge to the Refrigerator. Another way is to empty the stuff from the refrigerator door.Then remove the top hinge take off the door and place it on the counter on a blanket so as not to scratch the door. Replace the cam. Place the door back on the wooden blocks.Insert the Hinge into the cam while the door is standing on the wooden blocks. It would be a great help if you had a second person to hold the door so you don't gets bumps on your head. You first need to attach the top honge withe the 2 screws loosly so the door will move. Then screw the bottom hinge to the refrigerator. If you find that the inside of the door is rubbing lossen the top hing and adjust the door until it closed properly. Also by putting the stuff back on the door may cure the rubbing. Good Luck

I popped the rivet of the new hinge I received, removed the plastic bushing and installed it on my old hinge - this was the part that went bad on my old hinge. I re-installed my old hinge with the new bushing, problem solved

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

I followed the instructions verbatim as others explained. I did it step by step exactly as instructed, The timing was almost exact no more than 30 minutes. I removed the fan the night before the delivery of the new fan and used a small desk fan to cool the compressor. It worked fine in one half hour my freezer read a perfect zero. Thanks for all the help

Naturally you have to push the frig from the wall and unplug it form the wall outlet and while you are removing and installing the old motor and installing the new motor. Do not open any of the frig and freezer door untill you are finished and you plug the power cord back into the wall outlet. Remove the lower back panel with a screw driver or a 5/16th hex driver. It is a kind of carboard. Once all the screws are out of that panel pull the top out from behind the steel above and then pull it out from the bottom and set it aside. Unplug the power line off of the motor. There are 3 separate brakets holding the motor in place. 1st remove the fan from the motor by romving the finger nut off the motor shaft and then remove the 1st bracket screw from the bracket all the way. Then use a light to see the other 2 screws and you will see that you do not have to take them all the way out like the first one. Just loosen the other 2 and then turn the motor and brackets counter clockwise and then pull the motor and brackets all out as one from the right hand side of where the brackets were mounted. I took the motor and brackets to the counter and removed te brackets from the motor and installed them to the new motor making sure that the bracket with the one screw hole in it is mounted at the right place so that when you reenstall the motor and brackets will let the motor wire connector be the closest to the outside where you can replug the power cord back onto the motor. Install the fan onto the new motor with the new finger nut that comes with the new motor. replace the back panel and pkug in the power cord fot the frig and let it run. Mine ran a lot quieter after the new motor was plugged in. Have fun if you have to do it. It is worth it.

1.Removed defrost timer and replaced with new one.2. Removed panel on inside bottom of freezer compartment.3.Removed freezer thermostat and replaced with new one.4.Checked ohm resistance reading on heater element.It was ok. 5. Replaced bottom panel.6. Checked temperature in freezer and refrigerator for 2 days. Temperatures were as they should be. Checked drain pan under refrigerator to see if heater element was de-icing the evaporator coils. Tray had small amount of moisture in it. Working properly now.

made sure def. timer was operative. removed back panel of freezer section. found heaters bad, replaced elements also replaced sensor. I am 72yrs old so it took me longer than it should have,PartSlect send me the exact replacements parts that was needed. one day service

Connected the 2 wires and pushed in the switch until it clicked.

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

Removed floor grate,romoved screw holding timer,push timer back,removed hex-screw holding bracket,removed ground wire.Removed connectors from old timer and put on new timer,pushed back new timer,mounted bracket,screwed new timer to bracket. Set timer to defrost at 11pm,put back floor grate.

per your instructions

Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple