GSS25JETB General Electric Refrigerator - Instructions

I pried the switch casing out of the fridge panel with a butterknife, then unplugged the old switch. I plugged in the new one and popped the casing back in. Easy!

Removed panel from front of freezer door by pushing up on three spring loaded screws located in the opening where the ice door opens and closes. they are about 1 inch apart on the bottom of the opening. Push up to free ice maker panel. Remove three screws from solenoid, located at the top right. Remove wire, replace with new and that is it. Fixed the problem!! Our ice maker hadn't worked for months. Be careful if you remove the round ice maker door to clean. There is a spring that located on the left side of sprocket. The spring fell off and took me a while to figure where it came from. Recieved package in three days and the job took minutes. Works great! Very easy to complete.

This was a simple repair. I removed the broken bin from the refrigerator and snapped the white plastic handle / humidity control slide off the broken bin and snapped it onto the new bin. I replaced the bin in the refrigerator and loaded it up with veggies. Took all of 5 minutes to make the repair.

I followed the directions provided by Robert of Florida. My contribution is, be aware that the plastic nut on the auger shaft turns to the right to loosen.

By reading another customers tip I decided that my problem was the exact same. I had to order the entire motor not just the auger because the motor shaft was stripped. Once you remove the motor, hold the shaft with a pair of vise grips and use a screw driver to turn the auger off clockwise. The threads are reversed. The new auger screws easily onto the new motor counterclockwise and installing back into the fridge was a snap.

After removing three screws on the ice bucket, it basicly came apart by itself. I needed to use pliers to remove the old nut because it had over tightened itself onto the shaft. Be careful here - it is a left hand nut - not a normal right hand nut! Reassembly was a snap putting the parts back together in reverse order. Unit has been working great since the repair.

removed 3 screws with 1/4 " nut driver, unplugged 2 plugs by prying out on side tabs, removed bracket and motor. Used vice grips to hold motor shaft and used screwdriver to turn auger fork clockwise and remove. Unplugged two connectors from motor. removed 3 screws with 1/4" nut driver to remove motor. changed rubber boot from old motor to new. Reversed procedures to install new motor on bracket, auger fork, bracket in freezer, etc. Only difficulty getting both hands in narrow freezer compartment. Still didn't work, called repairman. When he got here I showed him the problem and lo and behold, now it would not dispense water. He diagnosed it as a bad motherboard, replaced it and all good now. Motherboard $150, diagnose and labor $90, but it is all good now and I even have a spare motor. The failing mother board causes strange howling noises at times and we discovered the compressor fan had also stopped working and in a short while I would have had a bad problem. Caught it just in time!!!

I followed the isntructions of another fellow who had repaired his ice maker, but made the mistake of taking the ice crushers apart before noting where the fixed blades were to be reassembled. Since there was not a schematic with the part I had to go on line to your site and enlarge and use the one there, while accurate, was very hard to read and when I finished, I think it is in the wrong place as I'm not able to get the fineness of crushed ice I had before the repair, but absent a very legible schematic I'm not going to try to fix it further. The auger works, gives us ice cubes and half crushed cubes.
Another tip for future repairers is to to wait for the ice container to warm up or use a hair drier on the part where the tabs need to be depressed to slip off the blade housing. When cold it's extremely brittle, but since I had to leave the job for later at one point and left in on my work bench I found it much more pliable and easy to assemble.
All in all, I'm OK with the part and the result, but wish I could have gotten the fixed blade back into the right spot.

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

Removed the plastic frame by pushing to the inside (all 4 sides), removed touch pad by sliding it to my right and disconnected the wires. Removed the four screws that hold the dispensing unit and replaced broken parts. Please note that I also replaced the funnel. Total cost of repair for DIY $30.00, savings by avoiding repair man, priceless.

We soaked the new gasket in warm water for a while and we pressed it into place. Really very easy. Working fine again.
Thank you!

pulled out broken bucket and auger assy. and slid in the replacement. works great so far. The easiest part was ordering the part and it didn't take very long at all to get it. Customer Service was very good at getting the job done. Thanks

Replace

The hard part was cleaning the dust around the coil and fan area. Its plug and play right after that. Two nuts on the fan housing and a wire harness snaps on and off. Bam! 1,2,3 Up and running. . Like new. . . Thank you ps

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.