TBXW22RRELWH General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lauraine from Rocky Hill, CT
- Parts Used:
- WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
family member melted fan with hair dryer
Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.
Was this instruction helpful to you?
Thank you for voting!
original parts broken (poor design)
Unscrewed four screws, two on each part, and replaced broken parts, reinserting screws. This is a no-brainer repair.
Was this instruction helpful to you?
Thank you for voting!
broken slide rails
Basically I removed 4 screws holding the rails together, did a little cleaning of the existing parts that I would re-use and screwed the 4 screws back in and put it back into the fridge. Piece of cake. If I hadn't cleaned up the old parts it would have taken me 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Keyport, NJ
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My wife forced the fruit drawer in and snapped the slide rail.
I pulled out the shelf and removed the 2 screws holding the broken side rail to the shelf frame. I then screwed the new rail in and set the shelf back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janette from huntingtown, MD
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
needed to replace broken drawer slide rail,
removed produce drawers, removed center piece front cover, removed glass shelf, removed broken drawer slide rail - unscrewing where attached in the rear of the refrigerator. Also removed screw from centerpiece where broken drawer slide rail was attached. reassembled all very quickly....saved myself having to buy another refrigerator by doing this simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from FARGO, ND
- Parts Used:
- WR24X445
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
had moved into new house and discovered freezer door gasket incompletely sealing tried using home warranty service but decided trying rather than 100$ service fee. ordered gasket and watched several u-tube videos.
Placed new gasket into dryer,( recommended by 2 u tubes) high heat for about 10 minutes and was a snap getting softened gasket into little tiny slot actual placement was done twice as there was a twist in the seal i missed the first time so did do twice but was so easy this way was almost sad thinking it would have been 100$ deductible having someone do it and who knows what normal cost would have been......thanks u tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Lewes, DE
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
no water to icemaker
removed back cover--disconnect water supply-- removed screw holding vave and unplugged the
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from WILLIAMSPORT, PA
- Parts Used:
- WR60X30349
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Evap fan failed, would need restarted by hand when weather warmed up
Repair was super simple. Everything was a direct fit. Hardest part was unloading freezer to access evap motor. My freezer was old making my wire shields very brittle so I cut the shielding and used heat shrink tubing for a neat clean repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nan from PURCELLVILLE, VA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My light in the refrigerator was going on and off.
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SUGAR LAND, TX
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch Not Working - Needed New Switch
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from EL PASO, TX
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
40 year old refrigerator brittle light switch fell apart
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from EAST JORDAN, MI
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light went out in refrigerator
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marj from NEWBURY PARK, CA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge light dead even with new bulb
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SCARBOROUGH, ME
- Parts Used:
- WR2X4550
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was leaking and causing the ice to freeze into a block.
People would use the ice maker and just let it grind and eventually the bin and the plastic cup at the end of the auger broke.
I replaced the ice maker and once satisfied it worked and did not leak, I took the bucket/auger mechanism apart and replace both the bucket and the ice cup.
While the Frig is getting old, it has paneling that matches our cabinets so we are trying to get a few more years out of this. This repair is one I should have done 10 years ago! Thanks Parts Select!
I replaced the ice maker and once satisfied it worked and did not leak, I took the bucket/auger mechanism apart and replace both the bucket and the ice cup.
While the Frig is getting old, it has paneling that matches our cabinets so we are trying to get a few more years out of this. This repair is one I should have done 10 years ago! Thanks Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie B from Hollister, NC
- Parts Used:
- WR23X318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
the ice dispenser quit working
I opened the freezer door and removed the access panel, then with a phillip screwdriver,I removed 1 scew and used a pair of pliers to pull the wires off.I then reversed the prosess.EASY
Was this instruction helpful to you?
Thank you for voting!