PDS22MBSBBB General Electric Refrigerator - Instructions

replaced lights in refrigirator and freezer

Removed main control board cover on back of refrigerator (3 screws). Unplugged power to refrigerator and removed electrical connections to control board using a screwdriver. Using a screwdriver disconnected (4) plastic self -locking prongs holding the board. Matched new replacement board with old board. Plugged in electrical connections to new board. Snapped main control board onto (4) self- locking prongs. Reinstalled cover (3) screws. Plugged in refrigerator and tested refrigerator operation.

Removed back cover from unit. unpluged wirring harness installed new control board and refigerator runs lik new

Part arrived 2 days before anticipated. I was able to keep my fridge running long enough to get the new part in, which took no time at all. The Main Board relay would start clicking and the compressor would shut down. By unplugging the top right plug for a minute and plugging it back in I was able to keep it running for a few hours at a time. Good enough to keep my food from going bad. Thr part was an easy plug in replacement, was a good price, and works great.

Removed the board cover from the back, removed old board, installed new board, installed cover.

No directions supplied with product. Be very careful to not break the old parts moving them to the new.

I could not complete the repair and by repair meaning removing the other parts from the original Lower Pan Frame and re-installing them on the new Lower Pan Frame so that the new Lower Pan Frame works as intended. The Lower Pan Frame contains other ancillary parts that must be removed and then reinstalled into the new Lower Pan Frame before the new Lower Pan Frame could be used as intended. The other parts were difficult and next to impossible (at least to me) to remove from the original Lower Pan Frame for re-installation into the new Lower Pan Frame. There are no instructions at all on how to do this unless one is very good at reverse engineering plastic parts that clip onto the Lower Pan Frame. I abandoned the effort and used the new Lower Pan Frame to the best I could. I would not recommend ordering this part from PartSelect. Waste of money for me ...

UNPLUG! (Read Instructions for wiring configuration) Remove cover lower back right hand side.Remove ribbon plugs top and bottom you will need to lever back holding tab while pulling plug they will more than likely break dont worry you are throwing this part away., disconnect ground wire, compress plastic holding tabs,
pull off control board, plug in new board push on to holding tabs reconnect ground and turn on refrigerator and check replace cover, everything is now working great.

I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

i Removed back panels and then I removed the faulty circuit board. Installed new circuit board and presto everything worked. I can't believe how easy it was but on the other hand I couldn't believe a refrigerator had such a sophisticated part..

1. Pulled refrigerator out
2. Unpluged the refrigerator
3. Removed the three screws holding the cover on.
4. Removed Board ASM Main Control.
5. Unpluged Connector's.
6. Pluged Connector's in to new Board ASM Main Control.
7. Put cover back on.
8. Pluged refrigerator back in.
9. Pushed refrigerator back into place.

Tom Paone at [email protected]. was very helpful at recommending that a solution to my problem was to replace the ASM Main Domestic Motherboard. I ordered and received the board in two days from PartSelect. After unplugging the refrigerator I used a nut driver to remove the three screws that held the motherboard cover in place and then disconnected all of the connections to the board. Next, using a pair of needle nose pliers, I gently squeezed on the white plastic anchor retainers that fastened the motherboard to the refrigerator. While doing this at each anchor I gently pulled on the motherboard until it was separated from the retainer anchor post. There were four retainers total. I removed the old board and in the reverse order installed the new board. All of the connectors were easy to match to the new board because the wiring connectors coming out of the back of the refrigerator were only long enough to hook to the correct connectors on the circuit board. There was an extra connector that I didn't use on the new board and also the connection for the ground wire used a ring connector instead of a spade connector. To remedy this I simply used the ground wire assembly from my old board. I also took the time to remove the lower cover on my refrigerator and cleaned the condensing coil with a vacuum cleaner. The total time to replace the motherboard and clean the condensing coil was about 20 minutes from start to finish. This repair solved the problem with my evaporator fan. A big thanks to Tom Paone at [email protected]. for helping diagnosis my problem and suggesting the correct replacement part. I saved between $100.00 to $150.00 not having to call out an appliance repair person to fix my refrigerator.

Followed the partselect video on how to replace motherboard and the video described the exact replacement procedure.

First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.