TBX18AHC General Electric Refrigerator - Instructions

turn off ice maker Shut off supply to fridge unplugged fridge unhooked water supply line unplugged harness plug to valve.

Hi, My furnace when out when I was away, frozen water lines were repaired, but my ice maker line was turned off, the valve split open. Summer is coming I want ice! I found the right replacement, ordered it, watched the free video, did the repair. It was so easy. And I saved an expensive service call. I am drinking a soda with ice from the ice maker as I type this! Thanks for solving my problem, I will be back next time something needs a part! Bob

easy pry out, disconnect wiring, connect on new switch and press in switch.

I opened the refrigerator door, slid the new crisper tray in and I was "in business! You are awesome! The refrigerator is 31 years old and I gave up trying to find parts in Seattle and decided to check on the internet.Thank you. It was all so easy!

I first disconnected the plug from the wall outlet. I then turned off the water supply to the back of the refrigerator. I then disconnected the two lines to the water inlet valve and removed the nut that holds the bracket to the refrigerator. I removed the water valve and installed the new one the same way in about 5-10 minutes. It was very easy, but, unfortunely that was not the problem.

Replaced single outlet valve for the ice maker

Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple

I removed the back of the refrigerator access panel disconnecte the 3 bolst holding the motor to the fan shroud assembly and removed the burned wires from the recepticle end at the wring harness. The fan motor comes with wire nuts but I chose to use the same style of connector as came with the OEM motor. I purchased the new connectors from NAPA and they are an exact fit. The new motor fit perfectly and has run flawlessly since the installation. It is in an awkward location and that takes time to get yourself into position but once there the assembly is very simple and it is rewarding to be able to use the appliance again. The ordering from the website and phone order are very easy to do and you have what you need in a timely and expeditious manner.

Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good

removed old valve, installed the new one. ice maker back to making ice.

per your instructions

Replaced valve kit and let it run. Took a day for the fill line to thaw and has been making ice like a champ.

I ordered the valve, which came only a day later. Mine is really simple because it only has one water line and one electrical plug in. I do not have a separate water filter. First, I unplugged the refrigerator and shut off the water supply. I unscrewed the cardboard piece from the lower part of the back of the fridge and freed the valve. I pulled out the top water tube that goes from the valve to the top of the fridge, that connects into the back of the ice maker. That tube was empty and dry - I blew through it to make sure that it was unobstructed, and it was. No water was getting to that tube at all. I pulled out the plugs from the valve, and unscrewed the water line from the valve and let that drain in the bucket. I had drained as much water in the lines as I could by flushing a toilet and turning on the sink until it seemed the water supply that was left in the pipes was low. Then I just did the reverse putting together everything with the new valve. I screwed back in the water line that runs from the wall to the fridge. I pushed in the water hose line into the valve until it was all the way in. It was uneven and frayed at the end of that thin hose line, so I cut it very straight across the bottom so it would be entirely flush when it was pushed all the way into the valve. Then I inserted the plug back into the new valve. I put everything back in place, plugged in the fridge and turned on the water supply. I had left the fridge out off the wall so I could check for any leaking. I left it overnight and by morning I had ice! It was so easy. My only difficulty was pulling out the thin water hose from the valve. I did not realize that you can push down on the circular rim and the hose just slips out. I think I saved a lot of money.

Googled the problem, came across this site where I learned what needed to be done to fix. Checked the part price, looked just for couriosity at the price from GE, it was WAY more expensive. Ordered the part, it arrived super fast, and shipping was next to nothing. The part came in, I replaced it. I made my husband so proud!!!