GTS16KBMERWW General Electric Refrigerator - Instructions

took old motor out put new motor in and fan blade all done

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

No problem, had the job done in twenty minutes,Thanks John

I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

My wife and I followed the installation video & put the gasket in hot water. We struggled to get it started in the second corner on top. Gasket had cooled down so wasn't wanting to go in the slot. I finally got the bright idea to use a hair dryer to warm the gasket as we pushed it along.
That helped us finish the installation.
Not sure the new gasket is the complete answer to the leakage at the top of the door (forming ice crystals). The MAGNETS ARE WEAK compared to my 1 year old GE top freezer refrigerator!
My newer refrigerator "snaps" shut.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

i found that the door was to low was the problem shimmed the hinge on the bottom brought the door up so the gasket was ok so isent the new gasket back to you never attempted to change so i dont have any thing to tell you about instalation difficulty carl phillips

Removed the back of the freezer, 4 screws, and then unscrewed the motor mount with fan and motor attached. Switched fan blades to new motor. Reinstalled motor mounting then back of freezer. I had to go buy the ring opener tool at the auto parts store. $12.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

The is my 'refreshment' cooler and sits in our garage. Hotter than heck in the summer so the things runs a lot. Started making a little growling noise. Had to partially disassemble the back panel to get to the fan. Touched the exposed shaft for a second and the sound stopped. OK, it's the fan. Went on line, used the (really great) exploded diagram to figure out what I needed. A couple days later the parts show up. Installed the new fan blade and retainer Removed the old motor (couple of mounting screws), connected the new motor (a plug in) and mounted the new motor making sure the grommet on the front and back were engaged. Turned the unit on and everything worked. Reinstalled the foam channel, the back panel and it ran perfectly. Great support (the diagram), fast delivery and fair pricing. Not bad!

Basically I followed your video replacement steps and it took me about 20 minutes to replace the fan and foam air duct. The video really made it easy to fix the problem of the refrigerator not cooling properly. Works great now. Thanks for your help it save me between 200/300 bucks to a repair person.. Don

I followed the instructions in the video. The decorative parts were slightly different than in the video, such as screws at the top versus the bottom, but all of the working parts were the same. I was somewhat hesitant about applying pressure to remove the locking spring and fan blades and to replace them but the video reassured me and all went well. The refrigerator is operating as quietly as when it was brand new.

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

I replaced the noisy evaporator fan motor after watching the video provided. All went well and now I have a much quieter refrigerator. I took apart the old evaporator motor to see why it rattled when moved and it had an electrical part that came undone and was the cause of the obnoxious noise that came from the refrigerator. Now, my wife and I can sleep better now that the noisy fan was replaced.