GTS22KCPC General Electric Refrigerator - Instructions

Gaskets designed to just press a flange into channel around doors. I tried everything..I pre-heated gaskets ; I put dish soap around flange; I used (carefully) a heat gun as I pressed gasket in. Really very difficult to get the gasket to seat fully. I don't know if there is a tool to help you do this, but you need strong fingers/thumbs and endurance. Once seated, you will need to heat the gasket to get it to fully seal against the fridge. Just lightly heat along the gasket with the doors closed and press open the fold with your fingers. I let the doors stay closed over night. Works great now, but I probably will call a repairman the next time. I miss the old gaskets with a zillion screws..PITA, but easier.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

Must have spent 10+ hours solid looking up info on the internet. Our ice maker had broken years ago, the door flap had broken years ago and I thought this was the end of a fridge after just 6 years 8 months.

GE offered a "broken appliance" warranty for $379 for one year, with no guarantee that when a technician came to look at it, the repairs would be covered by the warranty!!! No thank you, you just want me to buy a new fridge. Okay, challenge on, I'll fix it myself.

I took everything from the back of the freezer out. Spent an hour defrosting (note: use hair dryer next time). Ruled out a motherboard problem (even though it appears I have the old style motherboard), removed dust build up from fan intake. I could not get the heater to come on, so I cut off the thermostat defroster and connected the wires together. The only way to get the heater on was to set the freezer control to 0 / zero.

So, ordered part from partselect.com and it arrived the next day!!!. Installed and unit appears to be defrosting okay after a week.

So now I'm back to order the ice maker part. The door flap will wait for another time.

Note: I've put in the time for novices and recognizing how the freezer is constructed.

Time includes taking everything out of the freezer section, unscrewing everything, diagnosing problem, fixing the problem, putting everything back. I would say allow 3-4 hours and pat yourself on the back if you do it quicker.

Note#2, if you have a large build up there is a hole in the floor of the freezer section. If the water does not evaporate it will run out of the hole and into your wooden floors! Place towels both inside and outside the unit just in case!

Needed a square head screw driver.
Appliance man wanted $80 to come out plus parts. Part cost $20 and took 10 minuyto out on. Had to empty half the refrigerator. That took longer than the time to fox

Removed shelf from refrigerator, screwed on new shelf support, replaced shelf. Got a kiss from my wife for fixing her 'fridge.' Easy!

remove shelf above tray to access rail. remove broken rail. use screws from broken rail to attach rail to shelf.

I sent back the other one with the print out for FedEx that your company e-mail to me and then i put the new one in, very easy took a few min's
Thank you Mr. Phillip Lewis

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

I removed the top shelf and then the existing slide. I replaced the slide and then the shelves.

The only hitch was the need for a special screwdriver which cost $5.

Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!

I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.

So easy. It didn't look the same as the current one and I almost sent it back, but once I put the screws in , it went in so easily. Took me less than 5 minutes. I'm so happy!

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.