TFF19DTG General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dale from Millersville, MD
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
HInge Cam Riser next to lower door hinge broke and door would not close
The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.
Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.
Easy job .. around 20 minutes.
Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.
Easy job .. around 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Austin, TX
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The cams that allow the fridge door to automatically close had worn out
First I bought the right tool to remove the hinges.
Then replaced the hinge with the two cams.
Now the door closes itself.
Then replaced the hinge with the two cams.
Now the door closes itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vickie from Chandler, OK
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Refrigerator hinge broke
Use several wood blocks and propped fridge dooe up and someone else steadied the door while I replaced the hinge. Pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rocklin, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door sagged and would not stay closed
Don't even need to empty the shelves in the door.
Just prop the door up with a block of wood from the floor to the bottom of the door. Lay on the floor and replace the parts.
The door was acting up for a long time. I wish I had researched and repaired the problem a long time ago. Now it works great!
Just prop the door up with a block of wood from the floor to the bottom of the door. Lay on the floor and replace the parts.
The door was acting up for a long time. I wish I had researched and repaired the problem a long time ago. Now it works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Waterford, MI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door closing cam desintegrated
Took the stuff out of the door
Removed the door
Replaced the hinge
Put the door back in
Put the stuff back in the door
You may be thinking that I'm not much for words - but this was SO EASY that it doesn't warrant using more words than I did.
My 7-year-old son helped me - it was a fun father-son project.
Removed the door
Replaced the hinge
Put the door back in
Put the stuff back in the door
You may be thinking that I'm not much for words - but this was SO EASY that it doesn't warrant using more words than I did.
My 7-year-old son helped me - it was a fun father-son project.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- henry a from pennsauken, NJ
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
bad door hinge and cam
parts ordered fit perfectly made repair removed items from shelves removed door avd replaced hinges and reassembled 1/2 hour total by myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Camarillo, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Door wouldn't automatically close, dropped a bit
First removed plastic cover off top hinge with phillips screwdriver. Used nut driver to loosened screws on upper hinge to 1/2 inch out and then used wood blocks to shim up door as high as possible while still in closed position. Used socket wrench to remove lower hinge and fitting from bottom of door, while still closed. Installed new lower hinge and door fitting with socket wrench. Lowererd door to sit on bottom hinge and then adjusted position of top hinge before tightened those screws with nut driver. Reinstalled plastic cover. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tom from kincaid, KS
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door hinge worn out.
Laid a 3 1/2" block of wood about a foot long under door, pried up door level with other door and used a couple of wedges to hold door up. Used 1/4" sockets and ratchet to remove and reinstall hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from lesage, WV
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door stop broke
they sell the cam piece but the instructions says not to replace only one part. so beware you need both the cam and hinge as a kit .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Holbrook, NY
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door closing cams, top and bottom, became damaged and needed replacement
Turned refrigerator off. Removed food from right hand (refig.) door. Closed door. Removed upper hinge cover with a standard Phillips screwdriver and then removed upper hinge by removing two 5/16" bolts using nutdriver. Lifted door up to clear the bottom hinge-post and set it on the table. Removed the kick pan at the bottom of the refrigerator and then removed the bottom hinge-post which was attached with two more 5/16" bolts. Installed new lower hinge post and rubbed a small amount of mineral oil on the closing cam (which is riveted to the hinge-post). Removed the old upper closing cam from the door (5/16" bolts) while it as lying horizontal on the table and installed new cam lubricated with a small amount of mineral oil. dropped the door in place, replaced upper hinge and cover. Replaced kick pan. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Colfax, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Hinge assembly spacer at bottom hinge failed breaking up in small pieces
Followed other messages to complete fix. Simple overall.
Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.
Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Micheal from Longwood, FL
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Door dropped on the refrigerator side.
Removed all items from the door shelfs.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now level with the freezer door.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now level with the freezer door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Bath, MI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dorr would close properly
Lifted the door while closed into position even with freezer door. Then put srap pieces of wood under door to hold into place while I removed the old hinge assembly and replaced with the new one. The door works good now. Make sure you replace both peices as they will both be worn.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Manhattan, KS
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Closing cams were broken
1. Unscrewed the top screws with a socket set 2. Took door off of refrigerator 3. Unscrewed hinge assembly 4. Put on new hinge assembly 5. Replaced door on refrigerator 6. Screwed top screws back in I watched a youtube video on how to replace it that was extremely helpful. I am not a handyman, so if I can do this, anyone can.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from New Berin, WI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Door closing cams on door hinges cracked and sheered off. Door sit low on hinges.
Just watch the Parts Select YouTube videos on replacing the door hinges. That helped a lot.
All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.
All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.
Was this instruction helpful to you?
Thank you for voting!