Models > TBX18DAXARWW > Instructions

TBX18DAXARWW General Electric Refrigerator - Instructions

Jump to:

All Instructions for the TBX18DAXARWW
121 - 135 of 148
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Kenneth from Leavenworth, KS
Parts Used:
WR2X9391
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
light would not stay on
First I flipped breaker to off position for refigerator, Pulled down on socket and broke it free. Then took needle nose piars to pull wire and plug out from hole, so I could conect to new light socket then snaped it in place . Hardest part was getting wire and plug out of hole.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Williamsburg, VA
Parts Used:
WR2X9391
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
needed new light socket
Pulled out old socket.pushed in new one.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jules from Crowley, LA
Parts Used:
WR23X37285
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
Customer:
christopher from collegeville, PA
Parts Used:
WR23X37285
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cynthia from Seatac, WA
Parts Used:
WR23X37285
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
switch wouldn't come out anymore and turn light on
Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy
Was this instruction helpful to you?
Thank you for voting!
Customer:
huey from covington, LA
Parts Used:
WR2X8345
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
broken endcap
just pop it together
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gerald from Brunswick, OH
Parts Used:
WR2X8345
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Borken end caps on freezer door retainer
Took the broken ones off, placed the bar on the end caps and snapped them into the freezer door.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from North Chesterfield, VA
Parts Used:
WR72X273
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Right side rail of meat drawer cracked
Less than 5 minutes needed to remove cracked rail and replace with new rail. Must have a star wrench to perform task. Very simple task!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from Farmingdale, NY
Parts Used:
WR55X24064
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Both the fridge aqnd freezer would not get cold.
Easy. Followed the video instrucations. the part was right there next to the compressor.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James U from Pawleys Island, SC
Parts Used:
WR72X287
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
part did not fit.
was able to grind the edge to map it fit
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lloyd from Sumter, SC
Parts Used:
WR24X450
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Fresh Food Door Torn
My experience with PartSelect was excellent. My main concern was ordering the right gasket. First, I found the model number on the inside of the refrigerator. I ran model number on PartSelect and the compatible gasket came up. I removed old gasket carefully pulling it out. I cleaned around the groove that holds the gasket in and where the gasket lays. I boiled water and put it in a cake pan. I warmed up the gasket and smoothed and straighten it out. I started in each corner of the gasket and then worked from each corner pushing it carefully into the holding groove. Took me about 25-30 minutes. It seems to be working great!
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the TBX18DAXARWW
121 - 135 of 148