TPG24PFBABB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lou from Attleboro, MA
- Parts Used:
- WR38X10123, WR12X10192, WR12X10151, WR12X10132
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handles were getting discolored
took off the top and bottom ...they snapped right off ....unscrewed the actual handle and presto the refrig was ready for the new handles and covers.Parts Select is the cheapest, nicest and knowledgable appliance store I have ever dealt with. Keep up the customer satisfaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Carlsbad, CA
- Parts Used:
- WR02X11330
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
small leak in ice maker water tubing on the back side of the fridge
watched a 2 minute video on installing the connector. Then using the utlity blade cut out a 1/3" section of the tubing and installed the connector. DONE! Leak fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Dana Point, CA
- Parts Used:
- WR17X4152
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had a cracked grill on the outer part of icemaker/water dispenser
Ordered the grill and popped it in. This is the second part I have ordered from Parts Select. I previously ordered something for my microwave and the parts came very quickly too. I would highly recommend them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Boerne, TX
- Parts Used:
- WR02X11330, WR17X2891
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water leak at the nylon hose for chilled water service
The parts purchased worked perfectly and your write-ups explained what the typical problems are with this water leak that was occurring with our GE refrigerator at the nylon water line for chilled water service. Your description highlighted exactly what the problem was and the parts that I needed to make the repairs. This saved me a plumbing service call. All I had to do was cut off the nylon hose beyond the cracked area, apply the water nylon tube union joining the two hose ends and tighten the coupling at the unit.
Thanks again,
Jim Macdonald
Thanks again,
Jim Macdonald
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Durham, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost build up in ice maker
Watch online video on how to change icemaker flap! Video was great exactly how to do it, with a link to order the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Mooresville, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Dispenser Door Seal not sealing, frost in freezer
Googled how to replace the door seal, ordered parts and replaced the door seal flapper. The video on partselect was not correct for this GE model. However a simple diagran showed you simply remove the control panel directly (pops off) to provide access to the panel. Remove the 4 screws holding the panel, replace the door seal, and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Little Elm, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost buildup in the freezer near the ice chute.
I watched the video on the PartSelect.com website and decided to give it a try. The replacement of the flapper was even easier than I anticipated! The old flapper was extremely warped and was allowing air into the freezer. I'm not sure how/why it was in that condition but I am happy to report that I have no more ice buildup. Thank you, PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from Grand Blanc, MI
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
We had ice crystals on the ice tray and door
Removed the ice maker control panel and accessed the flapper door, easy switch out for new door and seal. The 2 year old warped seal didn't close and so ice crystals formed in the freezer - new unwarped part and Ta-Da no more problems :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Amissville, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper became warped. Freezer /icemaker frosting up... ice melting and sticking.
Popped off the front frame and front of mother board. unscrewed the assembly to be able to lift up to get to flapper. Lifted it up out of the the way ( wires are attached so it may take one other person to hold it up out of the way). Pop out the old flapper and replace with new one. Easy !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Kennesaw, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice dispense door flapper was deformed letting warm air into the freezer compartment.
The trim piece covering the opening of the dispenser is the first and most difficult part of the disassembly. Take care when removing this piece that it does not break.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Austin, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heavy frost was forming where ice is dispensed
Watched the PartSelect video. Very simple and solved the problem. Very pleased with the repair and PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Malgorzata from valley stream, NY
- Parts Used:
- WR02X11330, WR17X2891
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
plastic tubing that supplies water to the ice machine cracked
We have cut the broken part and using union connector we connected it back to the original tubing on one side and to the connector at the bottom. It was easily done with great help from the video on file at the site. Keep up a great work PartsSelect !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Houston, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice flapper replacement in freezer door
Looked at the instructional video and read previous customer comments. Didn't have to dissassemble rear of freezer door. Access through the front once trim ring and circuit board removed. Could not have done it with out the video/and or previous customer comments. Part was shipped and received immediately. Repairs complete! No more frost developing and plugging ice chute! I especially appreciate the customer comments on how to complete this repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Hughesville, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice dispenser chute kept freezing with condensation
The flapper on the ice chute was curled up and not creating a good seat, so the chute kept clogging up with frozen condensation, especially during the humid summer months. The online video made it so easy to replace the part myself. I was able to fix the problem in under 15 minutes and at a fraction of the price!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Chester Springs, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper was warpped
Follow instruction on the video you provided
Was this instruction helpful to you?
Thank you for voting!