GSG20IBMCFWW General Electric Refrigerator - Instructions

I took off the back panel in the freezer. Located the wires going to the old thermostat, cut them with wire cutters. I then spliced the matching wires together and attached the part to the coil tube (There is a little clip on the part, be sure to do this because I forgot and had to go back and do this again!!!).

Refrigerator was showing actual temperature of 80 deg, freezer was about 3 deg high. (house temp was 65 at the time) Defrost heater seemed like the only component able to heat that much, so the defrost thermostat seemed like the likely culprit. I followed the installation directions in the video, and the fridge has been fine ever since.

I ordered the part but my husband had to work out of town for a week. The fridge kept getting warmer, so when the part came I just watched the video on the internet, (bit the bullet) and did the repair just as I saw it done on the video. It was simple and exactly the same as the video. It took a little longer for me because there was a lot of ice built up on the coils, so I used my hair dryer to melt the ice. My refridgerator is working great now.

All the rest of everyone's post are all what I did. The only other thing I recommend is to put the back panel over the evaporator coils when your done. I replaced defrost thermostat, and heater. Once I initially completed it it kept icing over more than usual. You have to put the back panel back on so airflow goes over the coils.

My Ge top freezer fefrigerator was going into defrost mode and the heater was staying on for too long causing the food to thaw and eventually refreeze. Originally thought it was the mother board but after researching and do some troubleshooting of my own I realized the defrost terminating thermostat was bad. $8 part from Parts Select. Accessed the evaporator by removing back wall plate. Located thermostat and cut two lead wires to it. Spliced in new thermostat and reattached to eveaporator. Refrigerator seems to be good as new. There is an installation video on the web page that shows you step by step proceedure.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Remove the shelves then remove the back by removing the two screws at the top of the panel. Locate the temperature sensor on top of the coil. Cut the wires and replace with the new one. Use wire nuts and electrical tape to reconnect the wires.

The problem began when freezer thawed and could not keep food frozen. Initially, I thought the issue was the defrost heater (because I had seen similar symptoms previously and resolved the issue with a new defrost heater)and I replaced that part with a spare that I had puchased previously. The issue was still unresolved and I noticed the evaporator fan was not running in the freezer because it would not turn on when I closed the door. I checked to make sure I could hear the compressor working (and it was)and concluded that the evaporator fan motor was not running. I ordered the part and found a YouTube DIY video on how to replace it. While I was at work, my fiancee took it upon herself to watch the installation video and install the new evaporator fan motor and all is well.

I watched the videos before I received my parts. I thawed the freezer out, removed the panel in the back. Cut the wires to the defrost thermostat and spliced the new one on with wire nuts and tape. Then I did the same for the temp. sensor. Put it all back together. Now the freezer isn't running all the time. I set the temperatures back to normal and it seams to be fine.

replace sensor in refriger.

I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!

Removed the panel on the back wall inside the freezer side. To do this I unplugged the appliance, removed the racks, drawer, bulb and two screws holding the panel in place. The defrost cycle was not working so ice buildup on the coil was to the point of blocking air flow to the refrigerator side. I used a hair dryer set on high and stuffed two towels at the base of the coil to collect the melting frost and ice. Once the coil was clear of frost and ice I took the defrost timer off by sliding the clip off the tube, cut the wires and stripped the ends so I could use wire nuts to make the new connections . Placed the new defrost timer in the clip and reattached in the same location the old one was removed from. The sensor was replaced by doing the same steps. I replaced the panel after all the wire nuts were secured and the wires were tucked away where they would not interfere with the fan. Replaced the bulb, drawer, racks and food and plugged The refrigerator back in. 20 minutes from beginning to end.

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

Repair was rather simple. Removed the appropriate shelves and to make it easy to get to. Removed the ice container. I had to remove several items to get to the evaporator fan. Removed the ice dispenser motor cover, air duct cover, and the evaporator orifice cover. After all was removed the fan assembly was still attached to the orifice cover by the evaporator fan bracket. Remove bracket to remove the fan motor and assembly. Replace the all the old parts with the new and start the reassembly process. Really the only difficult part was working in such a small area. Good luck.

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.