GTS18HBMBRCC General Electric Refrigerator - Instructions

I pulled the shrouding off, unplugged the motor and replaced it. The hardest part is slipping the fan blade off the shaft without breaking it. Works perfectly now. Also, the shipping fed-ex, regular ground was only 3 days here to arizona. Would use anytime

took a little more effort than the video show to remove old module and replace new. Works fine now.

Easy

It was way to ez to install only a couple of minutes that's it

After removing 2 screws from freezer air duct and 2 screws and 2 self tapping screws from back panel, I removed all these, as well as the foam duct connector. Checked and verified 120 volts at the motor connector, indicating that the motor was bad. Ordered the motor, and 22 hours later, it arrived. 15 minutes later,and 6 screws reinstalled, it was up and running.

Simple door part replacement. Tenant issue. The parts arrived as I was told they would and it turned out I was able to fix one problem without the part so that part was returned and I am awaiting a refund. Other than that, I would certainly order from Parts Select again and am happy with your service.

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i

No problem, had the job done in twenty minutes,Thanks John

My wife and I followed the installation video & put the gasket in hot water. We struggled to get it started in the second corner on top. Gasket had cooled down so wasn't wanting to go in the slot. I finally got the bright idea to use a hair dryer to warm the gasket as we pushed it along.
That helped us finish the installation.
Not sure the new gasket is the complete answer to the leakage at the top of the door (forming ice crystals). The MAGNETS ARE WEAK compared to my 1 year old GE top freezer refrigerator!
My newer refrigerator "snaps" shut.

Removed the back of the freezer, 4 screws, and then unscrewed the motor mount with fan and motor attached. Switched fan blades to new motor. Reinstalled motor mounting then back of freezer. I had to go buy the ring opener tool at the auto parts store. $12.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

I followed the video instructions and the job was done in no time at all

Removed all the freezer inside panels to inspect the motor before I ordered the part. It looked like a relatively easy job to change it. I also watched the really nice video on the website that re-inforced my confidence in doing the job. The part came in a few days. I disassembled the freezer interior exactly as the video showed.(Warning: be careful with the styrofoam piece if the fridge is not fully defrosted. The ice build-up could cause it to break when trying to pull it out!)The only problem I had was getting the little collar on and off the motor fan shaft, and getting the fan off the shaft. I had to pull really hard for it to come loose and then I had to push really hard to get it back on the new motor shaft. I didn't know if could have used any kind of lubricant or not, so I didn't. After that the re-assembly inside the freezer went well, being careful to put everything back in the correct order and position. Started the fridge back up and it has been running very quietly ever since. But, most important, my wife was impressed with my work and is very pleased with the result!