TFF-19DV-D General Electric Refrigerator - Instructions

Removed top hinge cover and screws. Lifted door off bottom hinge and replaced bottom hinge assembly.

I followed the link to the how-to video that was provided on the parts-page, watched it and then followed the recommended steps. It couldn't have been easier -- and I'm not a "handyman." Thanks to PartSelect, I was able to diagnose the problem, find the part that was needed and figure out how to install it. I'm a grateful customer.

Removed both bottom drawers and then removed the old broken guides. Installed the new parts with a phillips head screw driver in just a few minutes. No problem.

put 4 screws in thats it

Remove both lower drawers. Remove 2 screws form the broken slide. Position the replacement slide and tighten screws. Replace the storage drawers. New parts were delivered within 2 days.

I did exactly as the video instructed. Removed the top hinge bracket. Removed the door. Replaced the parts on both the door and the freezer, taking care to save and re-install the shims. I put the door back in place and installed the top hinge. I also lubed the hinge pins with very light grease. The door now works perfectly.

One phiilps head screw driver and 15 minutes had my fridge repaired. Very easy and now I know where to quickly order parts and have the delivered almost as quickly.

Per you video. Without it I would have probably taken a lot longer that necessary. You will never know how much I appreciate your including the video. What customer service. Outstanding.

Removed the door, removed old hinge, aligned the new one. Replaced door, then adjusted the door so that it lined up correctly and had same size gape top and bottom between the double doors. Tightened up all bolts and screws and made sure door opened and closed properly. Watched the video that was available to show how to replace hinge correctly. This helped a lot.

Replaced broken part with new slide using 2 screws & screwdriver.

Followed easy video instructions. Loosened the necessary bolts, etc. Replaced hinge assembly, lined up door, lubed the hinge with vasoline. Works perfectly now. May purchase another assembly as spare as it appears this may be a common repair issue.

I blocked the bottom of the door(CAREFULLY!!) in position to elevate the door & take strain off the lower hinge & pivot post, while maintaining proper door alignment. I removed the two screws holding the hinge & post assembly from the frame, saving the screws & spacer for reuse. I removed the two screws holding the upper cam bracket on the door, again keeping the attaching parts. I installed and carefully aligned the new cam, original spacer & retaining plate to the lower edge of the door. I installed the new hinge & post assembly using the existing spacer & screws. I aligned the door & seal while checking the gap from top to bottom and from side to side. I carefully tighten the screws and rechecked the gap between the door & frame as well as the alignemnt of the door seal. Once satisfied with the alignment, I finished tightening the screws. I emphasize care and extreme caution in reinstalling the screws, they are a self-tapping (self-threading) type of fastener and this requires caution to make sure they are started and installed in the original threads of the door & frame. I put them all in using only finger pressure until I was positive they were started straight, going into the original threads, NOT trying to cross-thread or cut new threads, the structure is too thin for that and stripped threads will result! The door alignment and gap spacing is critical, make sure to check these adjustments carefully to ensure proper operation. Total time of repair, less than 15 minutes. I hope I have not over-simplified this because I have over 55 years of Automotive shop experienced and an ASE Certified Master Auto & Truck Technician...:-)

I removed the lower cover plate and placed a small scissor jack (used my car jack) under the refrigerator door, loosened the upper hinge, slightly raised jack to take the weight off of the lower hinge, removed the hinge with a 5/16 nut driver and the cam with a 5/16 socket. Installed new hinge and cam, removed door support and secured top hinge, check operation. Worked GREAT, did not have to remove door.

Set up two saw horses to put door on. Unloaded door shelves. removed upper hinge, and lifted door from lower hinge, placed door on horses. changed lower hinge on refrigerator. put door back on lower hinge, and closed door. Put upper hinge back on. Reloaded door shelves. It took more time to Unload, and Load door shelves than to replace Hinge.

Just used a screw driver to remove the old part and install the new one. The gal on the phone from parts select was excellent helping me find the correct part. Highly recommend this web site.