TFF-19DV-D General Electric Refrigerator - Instructions

I pulled all the items out of door, removed door top hinge cover, lifted the door off the hinge and removed the bottom hinge and closing cams and replaced them and re hung the door, just about that fast.

PS
Thanks for the parts

Being as the part is plastic it has a limited life span. But the repair is very easy and anyone can do it. I just proped the door with 2x6's and 1x2's and bolted it in. If you get confused just look at the freezer side to see how it goes, they are the same. It's four bolts and some shims that need to go in the same locations. I'm real happy that there is an online location to get these parts as there is not anywhere to get them where I live.

Since I ordered the right part thanks to the website, installing was easy. I just put the part in place and screwed the two screws into place. It took less than 2 minutes.

Removed two screws from the top hinge, two from the bottom - replace and put back together. It took longer to remove the food from the door than it did to replace it. THANKS

Trust me when I say that I am not a very handy person. It took only a matter of seconds to remove the broken slide rail, took 2 screws out. I found the part easily on the website, placed the order and the part was in my house in 2 days. My 12 year old son and I replaced the slide rail in a matter of seconds-required only the same 2 screws to secure in place. We replaced the glass shelf, slid the draw into place and now it is as good as new! A very easy repair!

Remove the 2 mounting screws, remove broken rail, install new rail and install 2 screws. I was finished in about 2 minutes.

After watching your instruction video and not wanting to shut down refrigerator and remove foods from door, I elected to lift the door and place blocking under it.The actual hinge replacement took approximately 10 mins. I would also like to say that I am extremely satisfied with PartSelects handling of my order and your promptness resending my order because of my goof-up with my own address. I am grateful and will recommend you to anyone who needs parts for any appliance. Thanks again. Chuck Gjovig

Removed old worn out slide rails and replaced them with newer ones.

replace broken hinge.

Laid a 3 1/2" block of wood about a foot long under door, pried up door level with other door and used a couple of wedges to hold door up. Used 1/4" sockets and ratchet to remove and reinstall hinge.

First issue, I tried to get the top hinge cover off by gently prying. No go. Went to get a step stool and discovered a small screw holding the plastic cover on. At least I didn't break it by prying. I then removed the two top hinge bolts and removed top hinge. I then lifted the door off the bottom hinge.

I then removed the bottom hinge (two bolts) and replaced it with the new hinge with the attached lift cam. (Bottom half of cam)

I then removed the broken lift cam from the bottom of the door, replacing it with the door closing cam included in the hinge assembly package.

Second issue: I did not need to order the DOOR closing cam as a separte item as it came with the hinge assembly package. (There was a warning note in the hinge assembly package to use the door cam included, as new materials had been used and abnormal wear could occure if you didn't replace both pieces of the lift cam)

I set the door back on the bottom hinge, replaced the top hinge and tested. The door would NOT close on it's own. Getting down on my belly I could see resistance of the door light switch was keeping the door from closing. The fix of this issue was to load the door with the normal use items. This provided enough weight to the door and offset the resistance of the switch. EVERY THING WORKED GREAT. Time was 26 minutes from start to finish.

Same as the others, just propped the door up and took off the upper and lower hinge parts and replaced them. One note: the old hinge was so torn up that some of the shims were partially destroyed. Since I didn't order the shims, I had to do a little machining. It might be a good idea to order shims if there is ant doubt.
P.S. With normal shipping, the order arrived in 2 days!

I read the details and bought the pair, as directed from other bloggers. I got the hinge piece, followed others advice and had it all done in not time! Saved a lot of money and will use this website again!

First removed plastic cover off top hinge with phillips screwdriver. Used nut driver to loosened screws on upper hinge to 1/2 inch out and then used wood blocks to shim up door as high as possible while still in closed position. Used socket wrench to remove lower hinge and fitting from bottom of door, while still closed. Installed new lower hinge and door fitting with socket wrench. Lowererd door to sit on bottom hinge and then adjusted position of top hinge before tightened those screws with nut driver. Reinstalled plastic cover. Piece of cake!

The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.

Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.

Easy job .. around 20 minutes.