Models > MSK25ZADAAA > Instructions

MSK25ZADAAA General Electric Refrigerator - Instructions

Jump to:

All Instructions for the MSK25ZADAAA
121 - 135 of 176
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Alan from Richmond, VA
Parts Used:
WR13X10020
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench set
The refrigerator door wouldn't stay closed; it popped open when we tried to close it.
I followed the link to the how-to video that was provided on the parts-page, watched it and then followed the recommended steps. It couldn't have been easier -- and I'm not a "handyman." Thanks to PartSelect, I was able to diagnose the problem, find the part that was needed and figure out how to install it. I'm a grateful customer.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alison from Lincolnton, NC
Parts Used:
WR13X10020
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Refrigeratior door of side by side would not close
I viewed a how-to video on partselect.com. I removed all items from the door shelves. Used a screw driver to remove the top "hinge" plate. Used a nutdriver to remove the door hinge plate. Removed door, laid on it's side-hinge side up (if you don't have a helper, lay it on a flat service). Simply removed the broken bottom plate and replaced with new part, and reinstalled on refrigerator. Super Simple!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from New Berlin, WI
Parts Used:
WR13X10020
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Refridgerator door was not closing properly
Followed the u tube video that was on the Part select website. Very easy install when following the video.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Valdosta, GA
Parts Used:
WR13X10020
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Door Wasn't Closing All The Way.
Did the repair jut like the instructions on the web site stated. There was a good video for doing this repair. Looked at it a couple of times and did the repair right off the bat. Thanks folks.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Apache Junction, AZ
Parts Used:
WR13X10020
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
lower hinge broken
removed door, replaced hinge, replaced door.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Connie from Woodstock, GA
Parts Used:
WR13X10020
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Freezer side door would not close
Followed the video to replace bottom hinge assembly. The only hiccup was that the video instruction was for the fridge side door, so there wasn't step by step instruction for dealing with the electrical connection at the top of door or the water line at the bottom. However, it was simple enough to figure out. Replacement took about 20-25 mins.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Larry from Ogden, UT
Parts Used:
WR13X10020
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Broken Cam on Bottom of Freezer Door
Removed door with little or no difficulty. Only time consuming portion of repair was disconnection and reconnecting of water line to door. This difficulty was primary due to age of the unit. After repairing, I determined that the cam on the refrigerator was also damaged so ordered same part to replace the refrigerator side.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brenda from Colleyville, TX
Parts Used:
WR13X10020
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Door would not stay closed
This was a Mother/Daughter feat. We viewed the video based on the bottom hinge assembly part that we had ordered. We did it exactly as shown and it was so easy. But while we had the door off we also had a chance to really clean the frigerator inside out. We were extremely happy that we were able to repair the frigerator oursleves and how much money we had saved by doing it. Thanks
Was this instruction helpful to you?
Thank you for voting!
Customer:
hs from kathleen, GA
Parts Used:
WR02X10140
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
door would not close on its own
like the man in the cd
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ruby from Riverton, KS
Parts Used:
WR13X10020
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Because the bottom hinge was worn out I couldn't close the door without lifting it first
After receiving the part (quickly) my son-in-law replaced the old one without any trouble. Thanks very much
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from Newcastle, ME
Parts Used:
WR13X10020
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Refrigerator door wouldn't close fully
This is a side by side freezer/refrigerator, nearly 30 years old. The repair was very quick and easy. 1. Remove two screws from top bracket. There is no cover for the top hinge on this older model. (2) Lift off door and set on kitchen table. (3) Remove two screws holding bottom door hinge. (4) remove two screws hold the cam and shims on the bottom of the door. (5) replace the broken cam on the door, and the bottom hinge assembly. (6) Replace the door on the bottom hinge. (7) Re-attach the top hinge screws, making sure the door is parallel to the freezer door. It took about 10 minutes to do all of the above. Best yet, I ordered the kit about 10am on a Monday, and the parts arrived, normal delivery, before noon the next day.PS- I used petroleum jelly to grease the hinge before replacing the door. The only tool I needed was a nutdriver.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruce from Ore City, TX
Parts Used:
WR13X10020
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Freezer side door would not remain closed
I did exactly as the video instructed. Removed the top hinge bracket. Removed the door. Replaced the parts on both the door and the freezer, taking care to save and re-install the shims. I put the door back in place and installed the top hinge. I also lubed the hinge pins with very light grease. The door now works perfectly.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Moulton, TX
Parts Used:
WR13X10020
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Hinge Worn And Cracked
Per you video. Without it I would have probably taken a lot longer that necessary. You will never know how much I appreciate your including the video. What customer service. Outstanding.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Don from Anaheim, CA
Parts Used:
WR02X10140
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
The door would not close from half way open automatically
First I watched the video and everything on that video was correct. I took off the hinge cap with a Philips screw driver on the top of the refrigerator. Then I took out two 5/16" screws with a socket wrench. Removed the hinge and the door lifted off. On the bottom of the door took out one screw and loosened the other one and replaced the Cam Riser. Put everything back together and it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Severna Park, MD
Parts Used:
WR02X10140
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
door making noise when closing
I replaced the cam. The video was really helpful telling me the steps and the tools that would be needed ahead of time. Took about 5 minutes because of the video vs It would have taken me 30 - 40 minutes if I didn't.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MSK25ZADAAA
121 - 135 of 176