GTR22KSPBRBS General Electric Refrigerator - Instructions

Once the part was received, it was very easy to snap the new part into place, and reinstall the drawers. No tools were required to complete the repair.

pull out the slide pan lh and replace for the part

Only problem we had was when we removed back wall on freezer the couls were totally iced up. After waiting for that to defrost. (3 HOURS) repair went fine. Was kind of hard to get to the part being its a side by side but happy with results

I was intimidated by this repair(as I am with most repairs), because there were 2 possible problems. But being able to purchase both parts for $30 (including shipping) made it worth a try. Thanks to the instructional videos that were sent, the repair was much easier than I anticipated. For me, the hardest part was fitting my shoulders in the narrow freezer. Now the appliance works like a charm. This would have been a $150-$200 repair had I called a company to do it.

I replace defroste thermostat :i defrost al the ice

Empty the contents of the freezer.Take out the one shelf.Remove the plastic pieces covering the fan and evaporator removing 2 screws with the nut driver.Remove the metal back using the nut driver(2 screws)Remove the fan assembly from the back of the freezer.(4 screws)Remove the green ground wire from the fan assembly(1 screw) Take the fan assembly out of the freezer and remove the old fan(2 screws) and reinstall the new fan.Assemble the parts in the reverse order .Very simple and intuitive for anyone who is "handy" at all.

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.

Removed the interior shelves and set screw which holds the light cover in place. Next I removed the four screws that hold the back panel in place. Located the defrost thermostat and removed it from the aluminum tubing by unclipping it, just as it was illustrated in the repair video. Cut the wires and stripped the ends and then connected them to the ends of the new defrost thermostat. Connected them together with an 16-14 gauge crimp style end cap. Taped the entry point into the end cap to reduce moisture penetration. Reassembled the back panel, light cover and shelves.

My defrost was not working, so from time to time I had to remove the accumulated ice with a hair dryer. I did some research and found out it is typically caused by a failing defrost thermostat, or temperature sensor. I purchase and replaced both for 30 dollars. Really easy. I watched the instruction videos on the site at least 5 times, so when I did it, it was like I was doing for the 5th time. Now the fridge works just fine!!

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

Removed the panel on the back wall inside the freezer side. To do this I unplugged the appliance, removed the racks, drawer, bulb and two screws holding the panel in place. The defrost cycle was not working so ice buildup on the coil was to the point of blocking air flow to the refrigerator side. I used a hair dryer set on high and stuffed two towels at the base of the coil to collect the melting frost and ice. Once the coil was clear of frost and ice I took the defrost timer off by sliding the clip off the tube, cut the wires and stripped the ends so I could use wire nuts to make the new connections . Placed the new defrost timer in the clip and reattached in the same location the old one was removed from. The sensor was replaced by doing the same steps. I replaced the panel after all the wire nuts were secured and the wires were tucked away where they would not interfere with the fan. Replaced the bulb, drawer, racks and food and plugged The refrigerator back in. 20 minutes from beginning to end.

took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.

I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!

per your instructions