ZISW48DCA General Electric Refrigerator - Instructions

Let me start by saying, I usually hire something like this out but figured I would give it a try. The install was fairly straight forward, however it would’ve been nice if the instructions would have been more useful. Instructing me to remove one screw to release the auger and solenoid enclosure wouldve been nice. There were 3 other screws that I didn’t need to remove and they were the ones holding the auger in place, which made assembling that much more difficult. Once to enclosure was removed, and the solenoid was exposed, it was a seemless process. I would however, recommend paying attention to or taking a picture of the connections on the solenoid. I was lucky to remember or got lucky. Regardless, I was able to complete the project successfully. If I had to do it again, I believe it can be done in 30 minutes or less.

I removed the one screw from the bracket that held the entire assembly in place. I then transferred the electrical connections and water lines one at a time from the old part to the new one so as not to mix them up. I reconnected the water line with the use of some plumbers tape. I turned the water supply back on to check for leaks. After not finding any, I placed the completed assembly back inside the refrigerator, screwed the bracket back into place, and I was done. Incredibly simple.

Turned off water
Took off the back panel
Removed water line from water valve
Remove electric plugs two at a time, attaching them to the new unit
Cut each water line, one at at ime, and pushed into new unit.
Reattached water assembly.

changed both inlet valves, did diognostic on old ice maker. replaced with a new one from partselect.I have a cupple notes of interest. One, do not count on the instructions sent with part , I't took me a while to figure out that they do not necesarly apply to my unit. no diognostic light on new unit. and you don't have to follow the same procedures. I finished the project but the added help hindered me more than helped.

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.

There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great

Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.

the previous left behind a side by side, everything worked however the auger in the ice bucket was a little rusty. I wish that I could say it was all me but the truth of the matter was the videos on file.

They were nicely done and easy to follow as I took the unit apart and replaced the auger in about 30 minutes. Thanks for all your help in part look up.

Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together

Since I really needed to replace the deteriating auger I used the original ice bucket and transferred the new auger assembly into the old ice bucket. Looked complicated at first, but make it work and my refrigerator is now making nice clean ice. It would have taken a lot longer if I sent the new bigger ice bucket back and it was my fault. With the videos and pictures on line made the replacement of the auger & ice bucket easy. Thanks Bill

Turned off the water and unplugged the frig. Removed the assembly (the hard part as it was corrodided) by removing 4 screws and slipping the electrical connections off. The water lines slipped off easilyThe instructions were good and the part fit easily. Then reversed the process by connecting the electrical and water.
I ordered the part via internet on Wed. evening and received it on Friday. Excellant service!

1) Shut off water supply
2) Pull out Refrigerator
3) Unplug
4) Unscrew back panel
5) Remove main water supply line
6) Remove bracket
7) Cut supply hoses 1 at a time and insert in new assembly in correponding openings
8) Reverse steps and enjoy

Notes: Judging by the new part's look, I suspect this repair will be needed again in about the same amount of time (5 years). The incoming pressure (I live in NYC) is probably too much for the way the part is built. Fortunately, now I know where to look , what to order and where to get it (great service, partselect.com!) it's no more then a 15 minute job.

Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.