PSC25PSWS General Electric Refrigerator - Instructions

I am going to start by talking about the problems. I woke up one beautiful morning around 4 am and grabbed my breakfast and coffee. I was not happy and realized there was a problem when the milk was almost as warm as the coffee. I was confused because I could hear the compressor running and the freezer was cold. On line directed me the right direction but I did not want to believe it. I did eventually confirm the evaporator coils in the freezer were frozen over because the heater was evap coil defrost heater was burnt out (multi-meter). I never realized a refridgerator had a heater, weird. The water dispenser in the freezer door had been freezing up for the past year. I could never find a real problem or solution to fix it. I did not find anything relating the evaporator coils freezing over causing the water line to freeze but thinking about the problem it made sense. The freezer was much cooler than it needed to be to cool the fresh food side. The temp control ensures the freezer is at least a certain temp, it did not limit how cold it would get. The hardest part of the repair was waiting for the part. I installation and reassembly of the freezer was easy. I replaced the cooling fan because the old one looked a little chewed up on the sides. It was not recommended or required. After the repair I was able to feel good airflow in the upper freezer and in the fresh food compartment. I think the fix will effect the temperature, the water line and also should help me get more ice from the ice maker (the freezer ducting feeds cold air to the ice maker area). Good luck.

I removed the cover on the back of the freezer side of refrigerator to expose the anti freeze element use the hair blow dryer to melt the ice on the coils put 2 towels to colect the water thats wath take me time, to replace the heath element was a 1 minute job.

took off the front panel, removed the auger and front piece, removed the pin and spring and installed them on to the new piece and then put everything back together

removed ice bucket from frig. removed screws to dis assemble the box to get to the auger assembly,removed stripped nut replaced reassembled be care not to let the rest of the assembly fall from auger there are a lot of blades and spacers to try to get back to proper position.

Took the tray out, removed three screws, popped the front tray out, installed the deflector, and put it back together. Done in less than 15 minutes and my wife is ecstatic that our dispenser works again.

Went exactly by the video. Perfect job, you send the installation video with the part. You watch the video before or during, goof proof, took longer to disassemble than to replace the part.

Changing out solenoid was very easy, but you don't have to remove trim ring and it didn't fix my problem. Turns out a relay fell out of its holder in the piece you have after removing the 4 screws per the video.

Watched repair video for replacement of water value. Be sure to consider water valve if Ice Maker is freezing up before replacing Ice Maker.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.

The right side of the three left three tines must be shaved about 1/8" to allow the ice remover blades to pass unimpeded.The part should be manufactured better.

New parts just snapped in place. Perfect fit.

Followed the instructions in the operator's manual to remove the door. Popped off cover of top hinge. Unscrewed the two screws holding pin down with socket set. Took off door. Unscrewed broken door stop with TORX socket. Replaced new door stop and reversed the process to replace the door. Very simple repair.

replaced lights in refrigirator and freezer

I got the wrong switch before so just need to put the right 1 in. Super easy, pop off old, plug in new, click back into place. Done. REALLY REALLY EASY for anyone to do