TBT18NABSRWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brad from SPRING MILLS, PA
- Parts Used:
- WR02X10098
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Noisy
I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from MEBANE, NC
- Parts Used:
- WR60X10168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Noisy Fan Motor
Simple. Rolled the refrigerator out , unplugged the 120 volts AC outlet.(1) Unplugged the wiring from the cabinet to the fan (white (three pin connector)). (2) Removed the two 5/16 inch screws holding the rear motor bracket . (3) Removed the fan blade from the motor shaft by applying slight pressure, pulling if off the old motor shaft. (4) removed the rubber isolator from the frame and from the rear of the old motor. (5) placed the rubber isolators back on the motor and frame. (6) Pushed the new motor back into the frame and re-installed the fan assembly. (7) remounted the fan with the rear support and the two 5/16 inch screws. Reconnected the three wire connector. Just checked the fan blade assembly to make sure they were not hitting the fan shroud. Fan blades should sit just partially inside the shroud to make sure it produces maximum airflow.
(8) Reconnected the 120 volt AC and waited for the compressor to cycle back on... Nice quite fan... Thanks
(8) Reconnected the 120 volt AC and waited for the compressor to cycle back on... Nice quite fan... Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rochelle from Culver City, CA
- Parts Used:
- WR71X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A cracked bar in the refrigerator door
I snapped out the old cracked bar and snapped in the new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boyd from Rapid City, SD
- Parts Used:
- WR02X10098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The evaporator fan in the freezer compartment began making a loud noise.
I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boris from East Lansing, MI
- Parts Used:
- WR12X10108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no problem
easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Owls Head, ME
- Parts Used:
- WR32X10500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken crisper drawer support
quick and simple--removed the old one and slid new part in on same support pins.I had the new part via UPS LESS THAN 24 HRS.FROM THE TIME I PLACED THE ORDER! THANKS, SOMEONE IS REALLY ON THE BALL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Danville, CA
- Parts Used:
- WR12X10107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The beyond cheap GE handle broke on our rental unit GE refrigerator after less than six months
The new handle just took three screws matching our model refrigerator perfectly--and it is much sturdier than the original. We originally went to the GE site and they wanted $70 +shipping for the same handle. Our landlord only paid $500 for this fridge six months ago--brand new! For a total of just under $17 we got a new handle in perfect condition--delivered quickly to our door. It was exactly as described and fit our model perfectly. We couldn't be happier and will tell all of our friends about this wonderful site. Thank you!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaNita from Petrolia, CA
- Parts Used:
- WR60X10168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The fridge was making a strange bird like whistle
The repair went smoothly and surpising easy! Get access to the back of the fridge. Unplug fridge, remove cardboard but save to put back in same place. For our fridge it was to bolts removed by socket set, removed old condenser fan motor (applyed a little pressure) and placed the new condenser fan motor in. It's easier with two sets of hands, but I've got to say DIRECTIONS OTHER THEN CUSTOMERS TESTIMONY SHOULD BE SENT WITH THE PART!! Otherwise quite simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Sarasota, FL
- Parts Used:
- WR12X10108, WR12X10107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The handles on my GE fridge had yellowed over 12 years use.
Just took the old ones off, the new ones went right on. Took less than 10 minutes. It`s nice to order parts and get the right ones on the first try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles R from Renton, WA
- Parts Used:
- WR60X203
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The bottom part of fidge was warm with water droplets on the its ceiling.
Removed Ice shelf,
Remove rectangle cover by removing the two screws and lifting straight up.
Pulled fan off slowly.
Removed two hex screws holding motor bracket.
Remove cover.
Remove two hex screws holding remaining bracket from fridge.
Pull wire off motor noting where they were plugged in.
Pull apart brackets holding motor and remove motor noting how the motor and brackets fit together.
Reverse to install.
Remove rectangle cover by removing the two screws and lifting straight up.
Pulled fan off slowly.
Removed two hex screws holding motor bracket.
Remove cover.
Remove two hex screws holding remaining bracket from fridge.
Pull wire off motor noting where they were plugged in.
Pull apart brackets holding motor and remove motor noting how the motor and brackets fit together.
Reverse to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cyril from holden, LA
- Parts Used:
- WR60X10168
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
not cooling
refrigerator was not cooling. with new fan the refrigerator is working so well I had to turn it down to "1" to get the temerature right.
Was this instruction helpful to you?
Thank you for voting!