TBX19JATFRAD General Electric Refrigerator - Instructions

The repair is somewhat self-explanatory. The old/broken rail which was broken needed to be unscrewed in front and rear, and the new one simply inserted and screwed in. Simple installation. What I REALLY wanted to share, is how impressed I was with the FAST service/speed that the parts arrived. Originally, we thought that just the middle drawer slide needed replacing, so I ordered the middle one and installed it. After installing it we realized that the right slide was broken too, so I ordered that. I placed the order on Saturday and the part was delivered to us on Tuesday!!! SUPURB service!! I will DEFINITELY order my next parts from PartSelect again!! Thanks for wonderful experience!

Soaked the new gasket in warm/hot water and snapped it on without any hassels. Thank you also for the fast delivery!

per your instructions

Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I ordered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.

Unscrewed the old rail, cleaned everything and installed the new rail

Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good

Removed slide from frame and replaced slide. Simple and easy.

Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple

Took out the vegetable bins, the glass and the shelf rack. Replaced the left side and the center glide. Worked easily.

My experience with PartSelect was excellent. My main concern was ordering the right gasket. First, I found the model number on the inside of the refrigerator. I ran model number on PartSelect and the compatible gasket came up. I removed old gasket carefully pulling it out. I cleaned around the groove that holds the gasket in and where the gasket lays. I boiled water and put it in a cake pan. I warmed up the gasket and smoothed and straighten it out. I started in each corner of the gasket and then worked from each corner pushing it carefully into the holding groove. Took me about 25-30 minutes. It seems to be working great!

Sears told me the part was no longer available. I came to your web site and then called your customer service. A very nice customer service lady helped me find the part. Very simple to pull the old one off and reinstall the new one with a rat trap behind the unit. Just in case it came back. Could have been a client but probably was a rat. Thanks for the great service.

Took the old frame apart - two screws - replaced broken side rail and put frame back in frig. replaced glass shelf and bins. Frig good as new. 15 minutes. Pretty good for and 81 year old lady.

Your online helpful hints made it easy as pie.

Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.

Googled the model number of refrigerator with symptoms of "refrigerator wont run". Parts select web site appeared on my screen, opened Parts Select website, Partselect said probable cause of my frige symptom was that the run capacitor usually burns out 51% of the time. They were correct with the diagnosis 100%. I ordered the run capacitor for $23.00, installed it in 10 minutes, refrigerator runs good as new. Thank you for saving me cost of service call. I probably saved $200 or more. I will use Partselect again with my next problem. THANK YOU,