TBE21ZRERWH General Electric Refrigerator - Instructions

Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.

I'll be back...

I followed the directions of Steve on the installation video. He makes it easy to do the repair with his step by step description of the installation. I have repaired three different aging appliances with help of Steve and PartSelect's very helpful Customer Service.
I wish Steve a wonderful retirement and hope PartSelect can find someone as easy to follow for future videos. The videos are priceless for the repairs.

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

Installed the new timer.

The part arrived It said to warm it to take out wrinkles but not even a picture of how to take off the old or put on the new. Everything on the internet in general about gaskets explained about unscrewing the old gasket but I couldn't find any screws. The user feedback mentioned no tools and that was our only clue and the only reason we finally succeeded. We looked at it repeatedly over 5 days. Pulled and pushed and could not figure out how it was attached or how to unattach without breaking things. I finally got out a screw driver and tried to pry it off. An hour later I got a corner piece started to come off. We pulled all the way around and got it off easily once started. We again struggled to put the new one on. Couldn't really tell what area of the gasket fit back into the crease. It kept falling off. Finally we pushed the correct edge of the gasket into the crease. VERY difficult. Fat edge fits into skinny crease. Took a lot more strength than expected so it didn't seem right but it was. Took a while and a lot of strength to work the corners and sides in. Eventually got the whole thing on. A picture and 4 sentences would have been a big help. Wouldn't try it again. To anyone else...No screws. Use a lot of strength. I hope someone publishes a picture for you.

I first unscrewed the broken right rail from the back piece and replaced with the new rail. Did the same for the left piece side. Attaching to the front rail was challenging because I took a while to figure out how to remove the cover (where the pictures of the vegetables/fruits are). But if you just get a narrow flat-head screwdriver under there, it just pries off. Then you can get to the little screw that attaches the side rails to the front piece.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

I pried the relay from compressor with small screwdriver, cut and replaced burnt wire going to relay,pushed new relay on compressor and wires unfortunately it did not fix the problem.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

I removed the original retainer and installed the new one.

Snapped end cap onto bar and installed bar onto freezer door.

I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.

I removed the Glass Shelf on top of the Vegetable Drawer assembly, unfastened the front rail from the broken slide rail and removed the entire assembly. I cleaned the parts and then installed the new rail. I placed the drawers in the repaired assembly and placed in the refridgerator. It really went well. I didn't need the other parts order. I only had them just in case they were needed.

I simply snapped the two end pieces into place, attaching the guard rail. It was like putting the pieces of a very easy puzzle together‚ especially for someone like myself who is mechanically challenged.

Put the new end cap on and snapped it into place, took about 5 seconds.