HTS18JBPW General Electric Refrigerator - Instructions

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

This is a built-in unit. Remove the external bezel at the top of the unit. Reach through the unit and unplug the frig. On the compressor unit, you'll see a vertical metal panel. Remove the metal panel and the timer is right behind it. Remove one wire at a time and switch it to the new timer. Remove timer and replace with new one.

Just an added comment, GE Service wanted to put an "ice kit" into my unit. The full repairs would have cost $1,000. While I described how to replace the defrost timer, the problem was the tray heater. But that's another story.

took out 4 screws - lowered timer cover - replaced timer- put it back together

I noticed that if I unplugged the refrigerator and plugged it back in a while later it would start working but eventually would stop. I deduced the problem was likely the defrost thermostat. I ordered the thermostat but it was in a difficult place behind the evaporator coil which I could not remove. While I was trying to work it into position my hand pressed against the defrost coil and shattered the glass sheath. I ordered the coil and finally managed to get it and the thermostat installed. The refrigerator seems to work fine now.

I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !

From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.

The part i received fit perfect, i just removed the old part and put the new part in with the screw driver.Really easy

Took freezer door off with torque screwdriver, unscrewed freezer door/refrigerator hinge with 3/8 socket. Removed refrigerator door and put on kitchen table. (Turn refrigerator off temporarily). Put freezer door back on temporarily. Pull out old gasket from groove on door. Put in new gasket. Take freezer door back off, put on refrigerator door, hinge, freezer door, put torque screws back in, your done. (Turn fridge back on)

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

First I had to go to the hardware store to buy a star bit to remove the old screws ($1.09). I attached it to my quarter-inch drill and used it to remove the old screws. I then used those same screws to attach the new slide. Once I had the star bit, it was little more than a five-minute task.

Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.

I'll be back...

two screws and a connector were removed to replace the timer.
Timer was located on the top front of fridge

I didn't call for repair iwas just order 2 pcs it's coming early morning in the next day I was happy 1hundred% I will recommend this company

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

Removed glass shelf, cleaned and set aside. 2 screws attach the old bracket, one on front, one in rear. Removing front screw requires popping off cover on front of shelf. (gently) Scrub off accumulated gunk. Install new bracket reusing same screws. Place shelf in fridge, making sure bin divider is attached to shelf with open end to front so that bins can slide into place. Slide glass shelf top back in place, do this gently, does NOT require force. Pop front shelf cover back on. Gently slide in bins. Done.