HTR18ABMW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Judy from NEW YORK, NY
- Parts Used:
- WR60X31522
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy motor that was getting worse.
Followed the steps on the linked video. Absolutely accurate and easy to follow. Beware: Don't drop a screw down the opening after removing the styrofoam block.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from CHAMBERSBURG, PA
- Parts Used:
- WR60X31522, WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fan became noisy
First unplug freezer and empty contents, then remove the screws from the air deflector, carefully remove styrafoam air deflector block then remove back panel for easy access. Fan will be easy to switch out from there. I highly recommend the You Tube video which is where I got my basic instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marj from NEWBURY PARK, CA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge light dead even with new bulb
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SUGAR LAND, TX
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch Not Working - Needed New Switch
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from EL PASO, TX
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
40 year old refrigerator brittle light switch fell apart
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SAN DIEGO, CA
- Parts Used:
- WR2X9162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My freezer door had a retainer bar that became disconnected at one end because the coupling broke.
I slipped the coupling over the bar and then into a door slot. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
Freezer & Frig Shelf Need To Be Replaced
When freezer door end caps & refig door end caps arrived just opened packages inserted end caps onto shelf bar and inserted the complete part into the slots provided on the frig and the freezer door. Needed no tools, just a little common sense. Took less than 1 min for both doors. Any one can do this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from ROCHESTER, NY
- Parts Used:
- WR2X8248
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wrong part shipped
Repair was not done using th part shipped. We went with the guide of the parts on the refrigerator. It would have helped if we could communicate (email or verbally)( with your parts center to verify the part we were ordering or on how to install it. We could wait for few days for a response. I am still waiating for instructions to return the part. It was a futile effort on both sides.
Your response would have helped tremendously..The picture was not adequate. Your group should be accessible to your customers.
Your response would have helped tremendously..The picture was not adequate. Your group should be accessible to your customers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from EAST JORDAN, MI
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light went out in refrigerator
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nan from PURCELLVILLE, VA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My light in the refrigerator was going on and off.
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from BATON ROUGE, LA
- Parts Used:
- WR82X10111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
had no access cover on back
screwed the cover on just like the original
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WALLINGFORD, CT
- Parts Used:
- WR2X9144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door retainer for condiments broke
Ordered new end clips and installed .Snap together parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sumlorq from Cleveland, OH
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch freezer door
put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Rowe, VA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bulb out
I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.
Was this instruction helpful to you?
Thank you for voting!