PTG25SBSARBS General Electric Refrigerator - Instructions

Replaced both the Defrost Thermostat and Defrost Heating Element. The You Tube repair video clips were extremely helpful for both operations. My difficulty was getting access to the parts that needed to be replaced in a very tight side by side freezer space. Otherwise, the repair went smoothly and the refrigerator is back in normal operation in time to save the perishable food inside.

removed 6 screws and repaced cover.

Removed the deli draw and removed supporting frame from bracket within the refrigerator. Snapped the replacement onto the deli basket support frame, engaging its retainers. Re-installed supporting frame and deli basket.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

After unplugging the refrigerator-freezer and emptying out the contents I snipped off the refrigerator thermistor, stripped off the wire insulation and used a butt splice. That did not solve the problem. So, a day later I unplugged the refrigerator again, transferred the freezer contents to a newly purchased small freezer unit, took off the back panel inside the freezer portion, and saw a large amount of ice build-up on the silver coils inside. This ice was quickly melted off using a hair dryer and packing towels below this accumulated ice. Then I snipped off the two freezer thermister sensors and the defrost sensor. I soldered the wires together for a hard splice, wrapped the individual wires with rubber electrical tape, and then wrapped that with plastic electrical tape. After re-assembly, the refrigerator-freezer has been working flawlessly for over a week at optimal temperatures.

Must have spent 10+ hours solid looking up info on the internet. Our ice maker had broken years ago, the door flap had broken years ago and I thought this was the end of a fridge after just 6 years 8 months.

GE offered a "broken appliance" warranty for $379 for one year, with no guarantee that when a technician came to look at it, the repairs would be covered by the warranty!!! No thank you, you just want me to buy a new fridge. Okay, challenge on, I'll fix it myself.

I took everything from the back of the freezer out. Spent an hour defrosting (note: use hair dryer next time). Ruled out a motherboard problem (even though it appears I have the old style motherboard), removed dust build up from fan intake. I could not get the heater to come on, so I cut off the thermostat defroster and connected the wires together. The only way to get the heater on was to set the freezer control to 0 / zero.

So, ordered part from partselect.com and it arrived the next day!!!. Installed and unit appears to be defrosting okay after a week.

So now I'm back to order the ice maker part. The door flap will wait for another time.

Note: I've put in the time for novices and recognizing how the freezer is constructed.

Time includes taking everything out of the freezer section, unscrewing everything, diagnosing problem, fixing the problem, putting everything back. I would say allow 3-4 hours and pat yourself on the back if you do it quicker.

Note#2, if you have a large build up there is a hole in the floor of the freezer section. If the water does not evaporate it will run out of the hole and into your wooden floors! Place towels both inside and outside the unit just in case!

Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.

I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

Installed the part with my hand. Two prongs inserted into preexisting holes in the refrigerator.

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.