GTS22ICSRC General Electric Refrigerator - Instructions

I removed the pan with the gliders attached. I used a socket set to remove the broken glider from the pan. Then, I put the new glider on and tightened the socket and put the whole apparatus back in the refrigerator. I am a 75 year old woman and had no trouble doing this myself.

I took out the drawer and the glass shelf.
All that was required after that was to unscrew the old part and replace it with the new one using the old screws. Very easy!

removed drawer, unscrewed old slide, screwed on new slide, voila! finished! I was very pleased with PartSelect -- ordering was easy, the correct part came quickly, and packaged very well. All of life should work so smoothly!

A very simple repair that took less than 10 minutes. About 5 of that was getting a screw driver and putting it back in the tool box. Simply remove the drawer, unscrew the two screws. Install new rail using the same two screws.

What I liked the best about PartsSelect.com was, I ordered the wrong part mistake. When I called to inquire about the refund/return of the un-used part, they were very polite and curtious. She said the return info would be in my e-mail in a minute. She even asked if I wanted her to order the correct part right then. I didnt have the model number with me at the time or I would have. A minute later I check my e-mail and there was the needed info. Excellent cutomer service PartsSelect. All my future orders, I'll check your site first.
Thanks,
Glen.

Took the drawer out, unscrewed 2 screws, replaced the part, put the drawer back in.

I removed the old broken part and replaced with the new part. Simple as pie, my husband was so happy and impressed I had it done by the time he got home from work!!!!

Took out the light sockets, plugged in the new ones. I found the manual on line to find the part numbers. Parts select parts were perfect

Needed a square head screw driver.
Appliance man wanted $80 to come out plus parts. Part cost $20 and took 10 minuyto out on. Had to empty half the refrigerator. That took longer than the time to fox

remove shelf above tray to access rail. remove broken rail. use screws from broken rail to attach rail to shelf.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Removed shelf from refrigerator, screwed on new shelf support, replaced shelf. Got a kiss from my wife for fixing her 'fridge.' Easy!

Remove one nut top of ice box cut wire and replace temperature sensor in freezer part remove two nuts on back panel and cut wire and add temperature sensor then remove defrost thermostat cut orange and pink wire and twist together new sensor and tape up and one more temperature sensor add bottom of freezer cut and replace and tape up all wire and replace back cover simple easy job

Replaced Temperature Sensor and now it is getting cold.

Disconnected the refrigerator for a few hours. On back of frezer compartment unscrew 4 screw to get access to Old defrost thermostat (D. T.). I cut the two wires with pliyers atached to D. T. Peel them about one inch both the old and new D. T. With plyier. Color coded put them together. I used those electrical cap wires to attach them toguether an electrical tape around it to prevent any moisture. Now working like new. Expend approximately $25. And 20 minutes of my time. (I was being charged for the repair. $250.) Now is working like new. Thanks

I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.