GSS22JETW General Electric Refrigerator - Instructions

I replaced the three sensors, 2 in the freezer 1 in the refrigerator. This was rated as the most common problem. Did not fix the problem. I then checked the ohms on the new sensors then the old sensors they were all within .5 of each other. So I got smart and went down the list of causes on their list. I emailed partselect and asked what the parts should read. They replied with that information and it turned out to be the voltage converter on the compressor. I ordered the part on friday payed for overnight delivery and it arrived tuesday. This as you can imagine makes me angry. But the part was easy to install and my refrigerator started working right away. I would advise anyone with this problem to start at the top of the problem list use a multi meter check everything on the list and only replace part or parts that don't come up to standards. This will save time and money and hopefully fix the problem the first time as you are not switching out parts and hoping that it solves the problem.

First turn off the power, remove the ice tray, remove the two screws holding the ice maker to the side of the freezer, use the screw driver to gently open the electrical clip for the power cord inside the freezer, remove the complete unit from freezer, bend the old stripper from the holding pin- it is flexible- it will bend, replace the new stripper on the holding pin and bend into the slot to hold it firmly, no water will come out from the fill cup into the freezer, plug in the power cord, mount back to side of freezer, you are done.

Part arrived in 2 days and took about 15 seconds to install. Great!! No more broken eggs!!

removed 3 screws unplug and remove old unit. install two screws install new ice maker, tighten screws plug in and turn on. had ice in 20 min.

avoided the problem for a few months and did not want to spend alot of money for a repair man. My husband is not the repairman type (he almost broke a light ficture trying to change the bulb). I went online and wasnt sure what I should order so I finally called, spoke to a woman who was very helpful, parts came in, removed broken pieces,used a screwdriver to put it in, put the light cover on and DONE! a new fridge! most rewarding 60 bucks spent in a long time...i should do more home repair!

Watched video, however could not get outer casing off. Under the panel are three small holes, pushed up with an Allen key, used a small screwdriver to wedge out, came out easily, followed instructions from video on removing and replacing solenoid

my 15 year old son did the install in 30 minutes
back in functional order and looks like

satisfied customer!

Bing , Bang, Boom.

The ice maker has plastic parts in the front that snap together. Getting those parts apart and back together was the most difficult part of the process. The auger was easily replaced.

It was more involved than I thought. I didn't have the proper tool for removing the snap washers but a screw driver and pliers did the trick with no damage. I think this is the first time I repaired something right the first time.

Excellent video on youtube showing how to replace the auger-Refrigerator and IceMaker Repair - Replacing the Auger Assembly (GE Part# WR17X11705).Very detailed video showing every aspect of this repair. There are many other videos showing this exact repair!!

Unfortunately, the replacement part didn't come with instructions. The repair, nevertheless, was fairly straightforward. After removing the plastic parts that guide the ice through the door (by removing a few screws that attach the parts to the inside of the door), I was able to slip my hand into the ice maker dispenser and remove the old part. The part clips on. It is a tight fit through the funnel (from the outside of the freezer), however, and requires that the gasket first be "flipped" open wherein it unfolds 180 degrees. Doing this will make it easier to clip the new gasket onto the assembly.

I followed the directions provided by Robert of Florida. My contribution is, be aware that the plastic nut on the auger shaft turns to the right to loosen.

Shut off water supply line to refrigerator, place towel or rag under corner of refrigerator where unit is located (to catch spillage when lines are disconnected). Remove back cover with 1/4" nut driver /loosen inlet line compression nut while unit is still attached(easier to loosen now than when unit is floating around loose)/remove unit from fridge then disconnect line and wires. Reverse process to install. Water lines going to water dispenser&icemaker are marked/wire connections are idiot proof. Check for leaks before pushing fridge back to wall. Thats not idiot proof!

Removed panel from front of freezer door by pushing up on three spring loaded screws located in the opening where the ice door opens and closes. they are about 1 inch apart on the bottom of the opening. Push up to free ice maker panel. Remove three screws from solenoid, located at the top right. Remove wire, replace with new and that is it. Fixed the problem!! Our ice maker hadn't worked for months. Be careful if you remove the round ice maker door to clean. There is a spring that located on the left side of sprocket. The spring fell off and took me a while to figure where it came from. Recieved package in three days and the job took minutes. Works great! Very easy to complete.