GTS22JBPW General Electric Refrigerator - Instructions

verify the heating element was o.k., found the top of the thermostat popped off,it had water in it,probably froze and came apart,cut the wires to the old thermostat and splice the new ones together,put the cover back on and verify operation

Ordered the part on Monday, it was delivered Thursday morning, and installed in less than 10 minutes. Part Select is awesome, would definetly use again!

We went for months not knowing where to get the part we needed until my husband found your site on line. The first part we received was wrong, but with the help of your operators, we then received the correct part. It was only a matter of removing two screws, placing the slide and then putting the 2 screws back in. It was a snap.

Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.

First I removed the glass shelf on top of the drawer. I then removed the drawer and unscrewed the old drawer rail. After this I cleaned everything, screwed in the new drawer rail, reinstalled glass and drawer and I was finished.

Unplug the refrigerator. Pull all shelves out of the freezer. Remove light bulb shield and light bulb. Remove the two hex head screws on either side of the light bulb. Wiggle out the back wall. It is a tight sqeeze, but can be done. Locate the sensor on the top of the coils. It is held on by a simple clip. Wiggle the sensor and twist a little to take it off. Take wire cutters and cut the two wires into the sensor near the sensor to allow lots of room to splice in the new sensor. Strip about a quarter inch of wires left in the freezer. Use some sort of wire connectors, like twist caps, which will allow you to connect the two wires to the new sensor. Make sure to match the colors. I used shrink tube and line connectors. Once you have the new wires spliced together and protected with either shrink tube or electrical tape, tuck the excess wire out of the way and attach the new sensor. This is easily done by slight pressure on the sensor with the tube in between the clip and sensor. Make sure the wires are tuck out of the way and reassemble the freezer panel, light bulb, and shelves in the reverse order.

I ordered the part but my husband had to work out of town for a week. The fridge kept getting warmer, so when the part came I just watched the video on the internet, (bit the bullet) and did the repair just as I saw it done on the video. It was simple and exactly the same as the video. It took a little longer for me because there was a lot of ice built up on the coils, so I used my hair dryer to melt the ice. My refridgerator is working great now.

Refrigerator was showing actual temperature of 80 deg, freezer was about 3 deg high. (house temp was 65 at the time) Defrost heater seemed like the only component able to heat that much, so the defrost thermostat seemed like the likely culprit. I followed the installation directions in the video, and the fridge has been fine ever since.

I just took the broken one and replace it with the new one that I ordered. very easy. Thank you!

Removed the old part using a phillips screw driver, cleaned the area, screwed in the new part, replaced the drawer. It was very easy to do, didn't even have to call my husband.

I thought I'd be nice and surprise my boyfriend by cleaning his frig for him. In doing so I broke the little plastic rail. I felt bad because the frig is not that old. I asked him where the owner's manual was, and he had no idea. Typical male. So I got on line on the GE website and tried to look up the part number, but they didn't have a diagram of the inside of the frig. I went to your website, found the part in minutes, ordered it, and amazingly it came in just two days. It sat on the dining room table waiting for him to fix it for 4 days. I finally got sick of looking at it on the table so that morning while he was still sleeping I grabbed my handy little cordless screwdriver, unscrewed the screws, slipped the new rail in, and screwed it in. It took less than 5 minutes. He got up later in the morning and asked me where I put the rail and glass top. I said "Where it belongs!" He was shocked.

I took the ice maker out then the panels that closes in the evaporator coil. Disconnected the defrost censer and tested it with an ice bath. The censer did not close the circuit. So it's bad. I got the parts .(Very fast I might add. The PartSelect team did a great job of getting it to me). I the stripped the wires and spliced the like colors back together and tested the censer again with an ice bath. It closed this time. I started the frig and have not heard anything from the client. In this case "No news is good news". Thanks PartSelect

I took off the back panel in the freezer. Located the wires going to the old thermostat, cut them with wire cutters. I then spliced the matching wires together and attached the part to the coil tube (There is a little clip on the part, be sure to do this because I forgot and had to go back and do this again!!!).

I followed the instructional video. It was right on the money for accuracy in terms of part location and method of replacement.

3 weeks After changing the defrost heater, i had to change the thermostat, part was suppose to come with wire connectors and everything needed, it didn't. Cut two wires to old thermostst, strip about a 1/4 inch of insulation and crimp new wires on part together. cover with heat shrink and heat with lighter until sealed.