TBX22ZPARWH General Electric Refrigerator - Instructions

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

I ordered the part one day and it was in my refrigerator by the next day. No tools required. You guys are incredible. This is the second time I ordered parts from you. You never disappoint!!

Wasn't sure what I would find underneath the old gasket, so I went slowly at first, but once the first side was off, the rest of the gasket came off quickly....and the metal track under it was clean and in good condition. After cleaning the areas where the gasket would seal, my daughter and I each started at a corner and placed the gasket into the track. Entire thing done in less than 10 mins. Piece of cake...only issue was a crease in the outer cushion area....I couldn't seem to smooth it with the warm water bath....it may uncrinkle with time...right now it is leaving a very small space when the door shuts. Saved me the expense of a new unit right now...hoping this takes care of the cooling issue I have with the unit keeping fresh veggies fresh.

I took all of the creases out of the new gasket with hot water as described on the delivery box. I laid the gasket on the floor and let it cool while I took the refrigerator door off, laid it on a table, and removed the old gasket. I started the new gasket into the groove at one corner and pressed it into place by sliding my thumb along the gasket and seating it as I went. It was an extremely simple task which took about 2 minutes. The most time is consumed in removing and replacing the door

Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

I removed the gasket starting in one of the corners, until the gasket was completely removed.
I then replaced the gasket with a new one by starting in one of the corners and pressing it on to the track around the door.

Pulled out old drain gromet. Have to be careful not to put drain in motor. Experienced repair person could probably to in 5 minutes; it took my husband about 15 minutes. Did not really need entire drain line; just connection at top.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Sears told me the part was no longer available. I came to your web site and then called your customer service. A very nice customer service lady helped me find the part. Very simple to pull the old one off and reinstall the new one with a rat trap behind the unit. Just in case it came back. Could have been a client but probably was a rat. Thanks for the great service.

I started at the compressor and replaced the overload and the Ptcr first and that did not make the compressor start running again, so I replaced the capasitor and it still did not start, so I bit the bulett and replaced the Main Control Board and that is what I should have checked first, when I removed the old one I found a little burnt spot on the back that I could not see from the front. The new one did not look exactly like the old one, it had two more wire terminals than the old one, but just leave them blank and everything will work just fine!

Had to e-mail GE for electrical schematic. Checked voltages to compressor. Jumpered compressor to see if it would even come on. Found bad run capacitor. Fixed.

take fan out,put new in

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

I watched the video, supplied on the website, two times and followed the procedure. The repair was very easy and a pleasant experience. Lay the new gasket out flat for a couple of days in the sun prior to installation and remove the door and lay it flat for the installation of the gasket. Remove old gasket and clean track and surrounding area thoroughly. Line up new gasket over track and at each corner and press into track, starting in center of one side, and work your way to each corner - repeat on each of the remaining three sides. Use a wet sponge to slide along the top of gasket while pressing same into track on the door.