TFX20SABEWW General Electric Refrigerator - Instructions

Unplugged the refrigerator then used the cordless drill to remove the 6 screws on the access panel on the back of the fridge to be able to get to the fan. Was able to pull the fan off by hand and push the new fan on by hand. Plugged the refrigerator by in and watched the fan run for a few minutes then replaced the access panel. Really quick and easy repair.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..

It seems my refrigerator was old enough [1987] that the spacing on the holes for the bracket were different than the part that is currently sold. The holes on the new bracket were 30 mm apart on center, but on the old bracket they were 20 mm apart on center.

Clamped the old and new brackets together in a vise to use the old bracket for spacing and drilled a new hole through the 4mm of steel.

After which it was a snap installing the new hinge assembly.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

Easy

The repair stories for this part are helpfull. The only problem I came accross was figuring out which part I needed to order. The parts diagram only showed one part labled 230, but when I used the drop down box to order the part there were 2 parts labled 230 for 2 diffrent prices. I called ge customer care and found out the less expencive part listed as 230 does not come with the wires etc. . The more expensive piece has the wire harness and every thing needed. I went with the more expensive part and it was a snap to install. . . .

1. Unplugged refrigerator from wall power socket.
2. Removed the 2 1/4'' screws and removed the back panel in the freezer section
3. Defrosted all of the ice off the coils and heater using a blower dryer which took about 10 minutes and lots of towels.
4. I replaced the defrost heater by following the provided instructions. I had a single element defroster which was replaced by a double element defroster. The instructions provided showed how to modify the wiring and were simple enough to follow.
5. Installed back panel and plugged in the refrigerator.

I checked on the defroster 1 week later and was pleased to see no ice on the coil. Problem solved.

took the panel out of the back of the freezer removed heating element put 2 screws back in the heating element for 2 screws back in the back of the freezer and the shelves

Removed the internal cover and used a hair drier to defrost the evaporator. Unpluged the conectorto the harnes. Placed new part in and pluged it in, replaced cover and tested.

Removed 2 screws holding top hinge. Removed door. Removed 2 screws that holds the door stop and cam riser replaced cam riser, provided, replaced stop and screws. Removed 2 screws holding lower hinge replaced with hinge, provided, replaced screws. Put door in place and replaced top hinge and srews. Job done

I removed the top hinge, lifted the door off the bottom hinge, rmoved and replaced the bottom hinge assembly, and reinstalled the door. I then aligned the door and reinstalled the upper hinge. The fridge works just like new!

removed door, removed old cracked riser aand replaced with new. You have a easy to follow parts site and very good prices. I will use you for all my future repairs.

Cake walk repair.

Unload the door then close it.
Remove screw holding plastic cover over hinge on top.
Remove 2 bolts attaching the hinge on the door.
Slowly open and lift door off of bottom hinge lay on counter.
Unscrew bolt, insert new cam, tighten bolt ,set back on bottom hinge, center install top hinge, tighten and install cover. tool me 6 minutes.

After recieving the part overnight (Very unexpected speedy delivery!) I propped the freezer side door up with a 4x4 and 2x4 and the old part came right off and the new part went right on with no hassels, Done in less than 15 min!!!!
The new part even came with step by step easy to follow directions.

After unplugging refrigerator and allowing freezer section to defrost completely I removed the lght cover in the freezer section and the green ground wire that is clipped to the panel. I was then able to get to the 2 screws needed to remove and pull out the back panel. I removed the failed heater from the bottom by disconnecting the blue and pink wires from the heater. I was replacing a single heater with a double heater so I needed to dress the blue wire down the right side of the evaporator. I positioned the double heater with the yellow jumper wire on the left and continued to connect the blue and pink wires into either socket on the heater. Be sure not to touch the bulbs with your fingers as they could be damaged by the oils on your fingers. Secure the heater by re-inserting the 2 mounting screws. Re-attach the green ground wire with clip to the back panel before you screw the panel back on. Restart the refrigerator and you are done. This was so easy and I saved over $120.00 doing it myself!!!!