TFF19DTC General Electric Refrigerator - Instructions

After watching your instruction video and not wanting to shut down refrigerator and remove foods from door, I elected to lift the door and place blocking under it.The actual hinge replacement took approximately 10 mins. I would also like to say that I am extremely satisfied with PartSelects handling of my order and your promptness resending my order because of my goof-up with my own address. I am grateful and will recommend you to anyone who needs parts for any appliance. Thanks again. Chuck Gjovig

replace broken hinge.

It was a trivial repair job -- just removed the Philips-head screws holding in the broken rails, and screwed in the new ones. (I also took the opportunity to scrub the bottom walls and floor of the fridge.) I'm just glad that PartSelect had the parts available, and that it was so easy to locate them!

Emptied door shelves and removed top pivot hinge bracket. lifted door of lower pivot and set aside.

Removed vent-toe base and replaced hinge 'L' bracket and cam.
Removed two bolts from bottom of door and inserted new plastic cam.
Set door back on lower pin and re-attached top hinge bracket while aligning door.

Replaced articles back in door and watched it as it it self closed. Total time, less than 15 minutes excluding cleaning of equipment while dis-assembled.

Part Number: PS290199

1. Empty the door shelves.
2. Leave the door closed.
3. Remove the grill directly beneath the doors.
a. It snaps in. Pull simultaneously on the outside edge and the bottom about 2 inches in from the outside edge.
4. Using two people. One holding up on the bottom of the door. The other removes the two screws that hold the hinge to the refrigerator.
5. Open the door slowly and let it down slowly to pull the door away from the top hinge.
6. Replace the new hinge half on the bottom of the door. Insert the other half of the hinge into the hole of the door to keep the other half lined up while tightening the screws.
7. Apply a small amount of lithium grease to the contact surfaces of the new hinge.
8. Using two people. One person is to hold the door. Best if he/she holds it from the bottom. The second person lines up the top while pushing up on the door to insert to the top hinge.
9. Insert the other half of the new hinge into the bottom of the door.
10. Line up the holes and insert the two screws that hold the bottom hinge to the refrigerator.
11. Reinstall the grill.

Used (2) 2 x 4's as block and lever to raise door removed 2 screws and removed door used same socket to remove and replace door side of replacement part. replaced door. This is the second time I have replaced this part on frig. side. Very easy replacement.

I pulled all the items out of door, removed door top hinge cover, lifted the door off the hinge and removed the bottom hinge and closing cams and replaced them and re hung the door, just about that fast.

PS
Thanks for the parts

I am a widow, 70 year old. Ordered parts. They came very fast. It took less than Fifteen minutes to remove door and take off broken parts and put the new ones on. I am glad I have two doors on the fridge so I was able to lift it up.

Being as the part is plastic it has a limited life span. But the repair is very easy and anyone can do it. I just proped the door with 2x6's and 1x2's and bolted it in. If you get confused just look at the freezer side to see how it goes, they are the same. It's four bolts and some shims that need to go in the same locations. I'm real happy that there is an online location to get these parts as there is not anywhere to get them where I live.

I was by myself so I took the entire Fridge door off. Took off the old hinge assembly and installed the new hinge assembly. The process took about 10 minutes and worked like a charm. Door closes like it did 15 years ago.

First, I loosened the top hindge bolts about halfway. Then, I took the bolts out ofthe door and then took the door off. Next I took the bottom hindge off and put the new part on. Then, reassembled the door in reverse. However, I didn't tighten the hindges until I made sure to align the door to close properly.

The magnetic door strip will hold the door in place if the door shelves are unloaded.I removed the bottom hinge with the socket set and installed the new hinge.

Removed two screws from the top hinge, two from the bottom - replace and put back together. It took longer to remove the food from the door than it did to replace it. THANKS

Removed the upper hinge assembly. Removed the door. Removed the kick plate. Removed the old hinge assembly and installed the new one.Replaced the other broken cam on the door bottom. Then,reinstalled door to fridge and reinstalled the top hinge. PS/cleaned and lubed both upper and lower hinges.

First issue, I tried to get the top hinge cover off by gently prying. No go. Went to get a step stool and discovered a small screw holding the plastic cover on. At least I didn't break it by prying. I then removed the two top hinge bolts and removed top hinge. I then lifted the door off the bottom hinge.

I then removed the bottom hinge (two bolts) and replaced it with the new hinge with the attached lift cam. (Bottom half of cam)

I then removed the broken lift cam from the bottom of the door, replacing it with the door closing cam included in the hinge assembly package.

Second issue: I did not need to order the DOOR closing cam as a separte item as it came with the hinge assembly package. (There was a warning note in the hinge assembly package to use the door cam included, as new materials had been used and abnormal wear could occure if you didn't replace both pieces of the lift cam)

I set the door back on the bottom hinge, replaced the top hinge and tested. The door would NOT close on it's own. Getting down on my belly I could see resistance of the door light switch was keeping the door from closing. The fix of this issue was to load the door with the normal use items. This provided enough weight to the door and offset the resistance of the switch. EVERY THING WORKED GREAT. Time was 26 minutes from start to finish.