GTH21GBEBB General Electric Refrigerator - Instructions

install icemaker water was allways delivered to previous unit water is not being delivered to icemaker still having difficulty

I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel and it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

Went well. Changed the Ice Maker and then the Water Valve. All good and it is making ice.

removed old valve, installed the new one. ice maker back to making ice.

Ordered the part from "parts select". Removed old part, installed new part by unscrewing the old switch, simply cutting supply hose ...pluging in the new part and re-attaching water supply line. 10 minutes at most.

I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.

After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...

had to replace copper water line to valve

Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.

Replaced single outlet valve for the ice maker

replaced valve.

water runs in now but still does not make cubes. just keeps dripping until I shut the water off.

Seemed simple and intuitive B U T the water tube receiver fooled me. Seemed to be on backwards. So, like my wife suggested, I D I D then read the installation instructions. Yeah! It's amazing what you can do when you just RTI. :-0

With help from this site, It was one of three things. I thought it might be what this site suggested the most common and it was. the valve in back of refrigerator at bottom. Water comming to it, but not getting past. Ordered part. Was here in a few days. Real easy to change out. A few screw / bolts and one wire that fit only one way. I did have to bend new bracket to make it fit. Now have lots of ice cubes!

Hi, My furnace when out when I was away, frozen water lines were repaired, but my ice maker line was turned off, the valve split open. Summer is coming I want ice! I found the right replacement, ordered it, watched the free video, did the repair. It was so easy. And I saved an expensive service call. I am drinking a soda with ice from the ice maker as I type this! Thanks for solving my problem, I will be back next time something needs a part! Bob