GLRT217TDB7 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marcos from E STROUDSBURG, PA
- Parts Used:
- 240362601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The Refrigerator was not cooling properly. At 40-45 degrees milk spoiled
My upper and bottom air diffuser was missing.
Purchased both air diffuser and placed it.
Purchased both air diffuser and placed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Sharpsburg, SC
- Parts Used:
- 240350609
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass
Order parts on sat.afternoon,and got part on Tues.aand installed in less them 2 min.
Was this instruction helpful to you?
Thank you for voting!
plastic drawer slide was broken
First I watched the video that provided - extremely helpful - thank you- when the part arrived I removed the drawer and shelf - unscrewed the screw- pushed the slide catches to one side and removed - then I screwed new slide on - pushed to lock in the catches and DONE! That simple - EASY PEESEY!! THANKS SO MUCH FOR VIDEO AND SUPER FAST NEXT DAY SERVICE - AMAZING HOW FAST!! WILL USE ANYTIME I NEED PART AND HIGHLY RECOMMEND YOUR SITE! TIME- 5 MINUTES TOPS!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Pilesgrove, NJ
- Parts Used:
- 240360801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost the temperature control know
The knob came in the plastic package. It was the correct part. I opened the package and placed the knob on the prongs. Now it works fine.
Thanks
John S.
Thanks
John S.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from STERLING, VA
- Parts Used:
- 5303918774
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Condenser motor burned out
I followed the instructions on your website, made it a simple as possible. Very tight work area sometimes fingers only, but a little patience works.
Saved at least $300. By not paying a repair person.
Saved at least $300. By not paying a repair person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Rio Rancho, NM
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old refrigerator door shelf broke
Installing the new shelf was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from woodland, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the freezer would stick in defrost and not come out
Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eddie from CHICAGO, IL
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The refrigerator wasn't getting cold the freezer was getting to cold
Followed the installation instruction for both parts now both the freezer and refrigerator are getting cold
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Pinole, CA
- Parts Used:
- 215846602
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Frost in freezer, fridge not cold
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from EAST JORDAN, MI
- Parts Used:
- 241733911
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
You have sent the wrong part for the THIRD time. You have sent aaccess cover that is TWO INCHES too short. It does not cover the opening, and you will not answer your phones.
There is no way to complete the repair with the wrong part, You have had my order since June 22nd, 2020 and the incorrect part arrived October 27th, 2020. You charged $7.79 plus $1.06 tax and $9.95 shipping. Please refund the entire amount including the shipping, since I did not ask you to ship the incorrect amount.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Los Angeles, CA
- Parts Used:
- 240530811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken meat pan on Kenmore refrig
Just slid it in. Fit perfectly. Called the Help Line just to double check that the pan would fit and they assured me it would. Pan cost $20 less than through the Sears site because of lower price, lower shipping and no taxes. Oh, and the pan came in just two days. Very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen H from Land o Lakes, FL
- Parts Used:
- 242201805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The crisper pan was broken.
Very easy.Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelley from KENSINGTON, NH
- Parts Used:
- 242201805
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Frame cracked and became brittle
Put old glass in new frame drop one side under small lip of frame..done..perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Lake Luzerne, NY
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
first fresh food too hot, then freezer too hot
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
Drawer rails wore out for the meat drawer
Took off worn out rails and replaced with new ones using a Phillips screwdriver.
Was this instruction helpful to you?
Thank you for voting!