PLHT217TAB0 Frigidaire Refrigerator - Instructions

I watched the instructional video and did what it said.

After disassembling, the thermal fuse I ordered were not and exact fit, I had to cut off the ring terminals, strip the insulation back and splice it in.
It works.

Removed drawer. Removed shelve. Flipped shelve over. Removed one screw. Undid tab on each end. Removed bad rail. Replaced with new rail and reversed order. Easy fix.

The knob came in the plastic package. It was the correct part. I opened the package and placed the knob on the prongs. Now it works fine.

Thanks
John S.

First I watched the video that provided - extremely helpful - thank you- when the part arrived I removed the drawer and shelf - unscrewed the screw- pushed the slide catches to one side and removed - then I screwed new slide on - pushed to lock in the catches and DONE! That simple - EASY PEESEY!! THANKS SO MUCH FOR VIDEO AND SUPER FAST NEXT DAY SERVICE - AMAZING HOW FAST!! WILL USE ANYTIME I NEED PART AND HIGHLY RECOMMEND YOUR SITE! TIME- 5 MINUTES TOPS!

Removed power , unplugged wires and 2 screws then reversed the process 1 hour later first batch of cubes dropped into bin

Order parts on sat.afternoon,and got part on Tues.aand installed in less them 2 min.

Took the drawer and shelf out then took the screw out and took the old one out and then put the new one on.

Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.

After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you

First I determined the icemaker was the problem when it was no longer calling for water. You can hear that "whistle" for 6-7 seconds when it calls for water. Anyway, replacement was a piece of cake, but did not entirely fix my problem. I also had to flush the lines to the soloniods that allow water to flow through the filter and into the water storage tank because it was cloggged with a little piece of plastic.

BOUGHT NEW ICEMAKER TOOK TWO SCREWS OUT, UNPLUGGED THE ELECTRICAL CONNECTION. REMOVED OLD ICEMAKER, PUT TWO SCREWS BACK INTO REFRIGERATOR(DON'T SCREW ALL THE WAY IN AS THE NEW ICE MAKER WILL FIT ON. HOOK ELECTRICAL CONNECTION AND ADAPTER (THAT COMES WITH IT). PUT THE DRAIN TUBE IN ITS SPOT, HOOK ICE MAKER ONTO THE TWO SCREWS TIGHTEN EM DOWN. I DID THIS RIGHT BEFORE I WENT TO A BIRTHDAY DINNER WITH MY HUSBAND, WAS ALREADY DRESSED AND READY TO GO AND I TOLD HIM ILL PUT IT IN SO WE CAN HAVE ICE WHEN WE RETURN. ENDED UP BEING A SURPRISE PARTY FOR ME AND WHEN WE RETURNED WE HAD ICE. IT WAS SO EASY EVEN A GIRL CAN DO IT!!

My upper and bottom air diffuser was missing.
Purchased both air diffuser and placed it.

inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!

I followed the instructions on your website, made it a simple as possible. Very tight work area sometimes fingers only, but a little patience works.
Saved at least $300. By not paying a repair person.