FPBG2277RF6 Frigidaire Refrigerator - Instructions

Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike

Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

VERY EASY SLIDE OLD ONE OUT AND PUT NEW ONE IT

Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.

THE repair very easy.

had to take off wheels to the old glass frame and put it on the new frame,

had to take off a few pieces to the old frame and put it on the new one that held the drawer on the support bracket so it would be put back in the refrigerator.

I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.

I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent

The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963

Removed the baskets/containers from freezer compartment. Removed back panel from the freezer interior.
Swapped the fan on the mount
Tested and reassembled fully
Back in working order

Full steps followed
https://www.youtube.com/watch?v=73rubWwQork

Remove the freezer drawer by unscrewing the two 12mm screws on both sides of the drawer.
Lift the drawer up out of the slots the frame and away.
Lay the drawer on a padded surface to protect the drawer cover finish.
Pull the old gasket out of the drawer and discard.
Position the new gasket around the edge of the drawer. Starting at one corner press the gasket into the slot in the drawer edge. Continue working the gasket until you return to the starting point.
Inspect the gasket to ensure it is seated in the slot completely.
Return the drawer to the refrigerator, placing the lugs on the drawer into the slots of the frame and insert the screws to their original position and tighten securely.
Inspect the drawer for proper level/sealing in the freezer drawer position. Adjust as necessary.

I watched the video and followed every step as outlined. It worked perfect, until I reconnected the supply line to my triple water valve. I used the old compression fitting and the compression nut. I should have cut the line and installed a new fitting and nut. The water on the floor the next morning reminded me of that. So back out I went and replaced the compression fitting and it has been as good as new. The ice maker took a few cycles to work again, I think it needed to fill the line with water first. But I have a huge sense of pride every time I hear water dispenced or ice dump in the freezer. Thanks for the help and encouragement!

Original unit had screw on lugs. After removing old unit, I unscrewed the lugs, cut the lines to remove the nuts and inserted them into the new unit. Everything was color coded so connection was simple. Reinstalled unit, cycled the ice maker several times only to discover the fill tube at in the freezer had frozen ice blocking the tray from getting water. Used a hair dryer to thaw out the tube, water flowed instantly. Very easy repair.

DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.

Gasket is held in place by an extrusion on the back side. Simply remove the old gasket and press the new gasket's extrusion into the track on the door.