FGUI2149LE2 Frigidaire Refrigerator - Instructions

The lower compartment was hovering around 50 degrees. Logic told me that cold air was not being driven from the freezer to the lower compartment. At first, I found the passageway between freezer and lower compartment was blocked with frost/ice, which could have been the entire problem. But why was that ice accumulated there? After defrosting, the problem was only partly solved. A few how-to videos suggested that the defrost timer was a common problem, so I tried that, the part was about $11, with minimal improvement. So I concluded that the fan was not driving cold air from the freezer to the lower section. I tested the fan by removing the freezer back panel completely, wiring the fan to an old ordinary power cord, and plugging that in to a wall outlet. The fan would not start on its own, would only turn if I gave it a spin, and then was very weak - I could stop it with a finger without pain! When my new fan arrived, I again removed the back panel in the freezer and replaced the fan, just a few screws to remove, then swap the fan blade to the new fan motor. The process was simple and obvious. Now the lower section stays near 40 degrees, though I'm not convinced that's the only problem-there seems to be a lot of variation in the temperature. BTW, I had also confirmed the defrost heating element was functional by activating the defrost timer (see youtube), to eliminate that from the diagnosis.

first i removed the four screws that hold the shelve in place disconnected the wire replace both diffuser-air,reconnected the wire and replaced the screws

just snap the new piece in place.

Followed the steps in the video on your site, really easy to do.

I slid the new glass in place

My 4 year old grandson used the frig door as a swing.The bottom hinge cracked, then the door wouldn't seal. I propped the door up with some books, removed the broken hinge (2 bolts) and replaced with the new part. Simple fix on the door, only time will fix the 4 year old!

the parts were exactly right and fit perfectly. they came quickly and arrived in great shape. I simply removed the broken pieces and replaced them with the new plastic frame to hold the crisper pans and the new pan.

Pulled the refrigerator out from the wall. Then unplugged it took my nutdriver with a1/4" socket on it and took out the screws from the cardboard back on the bottom of the refrigerator. Then I removed the two screws holding the water valve on. Then I unscrewed the supply water line from the main water inlet valve. Then I removed the outlet waterline going to the ice maker from the water valve. Then I reversed the procedure to put it back together. Hooked up the main water line and turned the water valve on for the water to flow to the valve at first nothing happened had to wait for a couple of hours for everything else to get to the right temperature before the ice maker would start making ice.

I ordered the Door Shelf Bin from PartSelect.com on Friday and received it on Saturday!! I was shocked, but thrilled. The easy to use diagram helped me to pick the right part and I easily replaced the broken one. I have already started to recommend PartSelect.com I was so thrilled with their service!

I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.

I recieved the part within 48 hours. I snapped the part in place and I was done in seconds.

Backed one screw off each side of the shelf brackets, snapped old ones out, snapped new ones in and replaced the screw. Spend more time taking food off the shelf than it did to make the repair

Removed the ice maker. Took off the cover and proceed to remove the motor. The only trick was to dis-assemble the electrical connector to replace the wires. I chose to do this rather than splice the new motor into the existing system and it was simple with a little patience.

Easiest repair to make and half / third the money for a new ice maker. The in-laws have ice again (it was over a year).

The old support just unscrewed & then the new one screwed right on with two screws.

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.