FGHG2368TF1 Frigidaire Refrigerator - Instructions

SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND

had to take off a few pieces to the old frame and put it on the new one that held the drawer on the support bracket so it would be put back in the refrigerator.

Original unit had screw on lugs. After removing old unit, I unscrewed the lugs, cut the lines to remove the nuts and inserted them into the new unit. Everything was color coded so connection was simple. Reinstalled unit, cycled the ice maker several times only to discover the fill tube at in the freezer had frozen ice blocking the tray from getting water. Used a hair dryer to thaw out the tube, water flowed instantly. Very easy repair.

Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike

I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.

very easy, make sure to watch the provided you tube video.

Twist to remove the old one an twist to install the new 9ne

Straight forward repair. Remove the four screws holding cardboard back. Remove the 2 screws holding the valve. Unscrew the water lines and unplug the electrical connections. I would caution that it would be wise to either take a couple photos or write down the order of connection. Even though it is somewhat color coded and the water lines are different sizes, a photo removes any confusion. My old valve had threaded connections using brass nuts and ferrules. The new valve has push in connections so you need to cut the ferrules off.. When cutting off the tubing, be sure to cut square. An angled or "squished" cut will leak when pushed into the fitting. Attach the valve to the refrigerator with 2 screws and replace the cardboard back and you're finished. While you have the back off is a good time to clean the coils. I left my fridge out and back off for a couple of ice making cycles so I could check for leaks (how I know the tubing needs to be cut very square). All in all, a very easy fix.

I removed the r/s drawer, removed the r/s shelf, transferred the metal brackets to the new shelf & reversed the procedure to reinstall.

carefully removed retainer from old valve

The part was easy to install and solved the problem! We had ice within hours. Thanks PartSelect!

FOUND ONLY TWO MOST COMMON FAILURES, NO ICE OR WATER KEEPS RUNNING/FILLING FREZZER. MAY CASE NO ICE BUT WATER CONTOL VALVE WORKED. REMOVER THE 4 10 MM BOLTS ON FREEZER DOOR AXCESS TO THE THREE PHILLIPS SCREWS ON BOTTOM OF ICE MAKER DISCONECT WIRES, AND LIFT OFF HANGERS, REINSTALL ALL REMOVED PARTS. NOTE! DID SHUT OFF AND DISCONECTED POWER BEFORE REPAIR. WORKS FINE NOW.

The u tube instructions were exactly what is needed. I had to cut off the old plastic pipes. My pipe had threaded connectors. Pex push on connection is super easy. You don't really need a block of wood to cut it if you have a sharp utility blade. If if you are sure this is the problem this is a really easy fix. Steps 1 turn off water at wall unplug electric also 2. Disc line at valve on refrigerator 3. Remove 2 screws holding valve 4. Pull valve out and remove plastic hoses and electric connections pay attention to color of pipe and electric connection. Mine were color coded. Had to cut off thread connectors. Reattach in reverse order or do one at a time. Check for leaks.

Removed screws and rail and installed rail and screws

Just place new filter and lock it!