FGHG2366PFCA Frigidaire Refrigerator - Instructions

Original unit had screw on lugs. After removing old unit, I unscrewed the lugs, cut the lines to remove the nuts and inserted them into the new unit. Everything was color coded so connection was simple. Reinstalled unit, cycled the ice maker several times only to discover the fill tube at in the freezer had frozen ice blocking the tray from getting water. Used a hair dryer to thaw out the tube, water flowed instantly. Very easy repair.

had to take off a few pieces to the old frame and put it on the new one that held the drawer on the support bracket so it would be put back in the refrigerator.

Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was

Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.

Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.

I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.

I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent

The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
[email protected]
8042627963

Can't supply any info that would be helpful. Ordered a " badge" that covered 100% of the scratch and stuck it on. Scratch now covered and problem solved. Thanks for asking.

had to take off wheels to the old glass frame and put it on the new frame,

DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.

Basically unhooked water lines and removed the screws

Straight forward repair. Remove the four screws holding cardboard back. Remove the 2 screws holding the valve. Unscrew the water lines and unplug the electrical connections. I would caution that it would be wise to either take a couple photos or write down the order of connection. Even though it is somewhat color coded and the water lines are different sizes, a photo removes any confusion. My old valve had threaded connections using brass nuts and ferrules. The new valve has push in connections so you need to cut the ferrules off.. When cutting off the tubing, be sure to cut square. An angled or "squished" cut will leak when pushed into the fitting. Attach the valve to the refrigerator with 2 screws and replace the cardboard back and you're finished. While you have the back off is a good time to clean the coils. I left my fridge out and back off for a couple of ice making cycles so I could check for leaks (how I know the tubing needs to be cut very square). All in all, a very easy fix.

I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.

very easy, make sure to watch the provided you tube video.

Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike

slide old filter out and insert new one