FRS22VSBD0 Frigidaire Refrigerator - Instructions

After pulling the fridge away from the wall and opening the paper backing on the bottom, I could see the motor. It's affixed to 3 metal ribs by 3 small screw/nuts. There is also a 12" wiring harness that led to a simple disconnect. Removing the disconnect and the 3 nuts was easy. However, there was no room to remove the motor with the fan attached. Between frame parts, the drip pan below, the ribs, and small, delicate copper tubing that can't get bent, it wouldn't fit thru any openings. So we rotated the motor inside the framework until the blade faced out, then reached in with a pair of needle nose pliers to remove the washer. Removing the washer is easy, it's just difficult to reach. With the washer off the fan was out of the way and very carefully (it was tight) the motor came out. Reverse was the same issue. Motor tight going in, not a lot of room to maneuver fan onto motor, and needed needle nose to tighten washer again. Make sure you tighten the washer before you install the motor on the prongs. Otherwise you need to remove it from the ribs, twist it to face you, then reinstall it on the prongs. Also, I felt I was stripping the nuts into the new motor. Turns out the holes in the motor aren't tapped. i realized the nuts are self tapping once I looked at them. I'm a big time DIYer and this wasn't bad at all. If your motor/fan assembly comes out whole, it's even easier.

Remove ice pan below ice maker. Got mirrow verifed the type of screws. Obtained nut driver and felt it at right angle remove screws only have way. The ice maker lifts up and off. Took needle nose pliers to grip and remove electrical connection plug. The instruction and picture sent was no help the picture were the size of a thumb nail no detail could be determine. I installed the adapter plug and all the extra length wiring was the most difficult to type wrap with both hands extended out in front. I finally wrestled it in on to the two screws unscrewed from the wall about 1/2". Keep the ice maker water lever up and ensure it aligns to the water trough inlet. Works Great.
glg

I removed the housing at the top of the refrigerator compartment that contained the reefer light and temperature adjustment knob. This required a small nut-driver. Inside, I found the old defrost control, unplugged it, unscrewed it with a Phillips screwdriver, and replaced it with the replacement part. Then I replaced the housing to its original position.

Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.

Great resource and service, thank you.

The repair was extrememly easy and took about as long as it did to order the pasrt online. Just removed the front drawer handle with a screw driver ,slide it onto the new storage drawer and reinstall. Less than 5 minutes.
C.J.
Rochester Hills,MI

Removed four screws for cover on refrigerator temperature controls, unpluged old timer and pluged in new timer. Replaced cover and screws.

Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.

Ice maker is held by 2 screws just above the unit, on the wall of the refrigerator. You can't see the screws, so borrow your wife's makeup mirror. Shine a light into the refrigerator, and using the mirror, locate the two screws, holding the unit in place, on the wall of the refrigerator. Using a nut driver, or socket wrench, with a 1/4 in socket, loosen up the two screws, but don't remove them. Bump the unit upwards, and away from the screws. (BEFORE doing anything!! Shut off the water supply, unplug the refrigerator) When you get the unit freed up, just unplug the old unit, and install the new one. You don't even have to worry about the water lines, and you'll see why, when you get the old unit off. Just reverse the procedure, installing the new unit. Very Simple, 10 to 15 minutes tops.

1. Turned off the cooling cycle and unplugged the refrigerator.
2. Removed all of the shelving and bottom basket.
3. Removed rear covering in the freezer section.
4. If frosted over, manually defrost coils with hairdryer.
5. Located original thermostat and after marking the wire locations cut the wires and removed the Thermostat.
6. Connected matching wires using a lighter to melt the wires together. Wrapped repaired wires with electricians tape.
7. Unable to install the thermostat in the recommended location (freezer is a tight fit) the new part was installed at the original location.
8. Replaced the rear cover and shelves.
9. Plugged in the refrigerator and set the cycle back to cooling.
10. Monitored freezer coils couple of days/weeks depending on how fast they freeze over (slots at bottom of cover) to validate if problem solved.

Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.

The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.

Removed old drawer, removed front pannel. Installed front pannel on new drawer and reinstalled ing fridge

no problems

I removed the plastic shroud on the ceiling of the refigerator, unscrewed and unplugged the old defrost timer, and replaced it with the new one. I reinstalled the shroud with the new timer installed.

Removed shelf brackets to allow the removal of the evaporator sheetmetal cover. Unpluged wires to thermostat ,removed defrost timer and plugged in new timer,(front left lower kick panel). Cut and resoldered wires to new thermostat reinstalled thermostat and cover in reverse order. I knew what parts I needed and how to repair the unit,however your customer comments were spot on and would help anyone perform a successful repair (you provide a helpful service for the public)