FGUI2149LP3 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- GEORGE from CAMBRIA HEIGHTS, NY
- Parts Used:
- 241808201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Bin
I just replaced the door bin. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Jonesboro, GA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wife didn't like the upper freezer door bin.
Replaced it with one like the lower freezer door bin. Very easy, just snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Los Angeles, CA
- Parts Used:
- 240530811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken meat pan on Kenmore refrig
Just slid it in. Fit perfectly. Called the Help Line just to double check that the pan would fit and they assured me it would. Pan cost $20 less than through the Sears site because of lower price, lower shipping and no taxes. Oh, and the pan came in just two days. Very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelley from KENSINGTON, NH
- Parts Used:
- 242201805
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Frame cracked and became brittle
Put old glass in new frame drop one side under small lip of frame..done..perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colline from PENDLETON, OR
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker not making Ice
Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from GILBERT, AZ
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
made lots of noise
Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from ELKHART, IN
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right side meat drawer rail cracked
1] Pulled the meat drawer out. 2] Removed the shelf holding the meat drawer. 3] Unscrewed the right side rail. 4] Installed the new rail and screwed in place. 5] Re- installed the shelf and meat drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from POMONA, CA
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken right side rail on meat drawer
Removed two top trays, fixed the rail on the second tray by removing one screw and sliding out broken piece, and sliding in new arm and rescrewing. Screw was a little tight, but went in.Very impressed i was able to do it myself with your simple instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cristina from MARLBOROUGH, MA
- Parts Used:
- 242193213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old gasket was torn and falling out
I removed the old gasket and cleaned the area. Then I started at the bottom and pressed the new gasket into the door. You must use firm pressure and go all around. It does get tricky hear the end as it seems like there is excess, but it will fit. Just keep using firm pressure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- henry from alhambra, CA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
my ice maker stopped working
removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from VIRGINIA BCH, VA
- Parts Used:
- 241554901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Door switch was no longer making my light go on when door opened
I used the youtube you provided. It was pretty straight forward, but I had to make a trip to the hardware store for a bit (hex wrench) to remove the hex bolt head style screws. I was only expecting to need phillips or flathead. I managed to remove one with a set of pliers, and the brought that example to the store for size reference when buying the bit to fit my black and decker drill. The rest was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from N LAS VEGAS, NV
- Parts Used:
- 240350609
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The glass shelf broke above the 2 drawers on the bottom
Just lay the new glass shelf into the groves. The shelf was too big and would not fit properly down into the groves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TUCSON, AZ
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light not turning on when door opened
Used a flat head screwdriver to pop out the old switch, removed the contacts and placed on the new switch, popped the switch back in. Done in about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
Drawer rails wore out for the meat drawer
Took off worn out rails and replaced with new ones using a Phillips screwdriver.
Was this instruction helpful to you?
Thank you for voting!