FGTR1845QF3 Frigidaire Refrigerator - Instructions

The repair didn't require any tools at all. Just simply slide the new glass shelf carefully into the the frame and while holding it horizontally slide the frame back into the rails. This took less than a minute to accomplish. Very satisfied with the results.

I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!

Don't ever tell your 11 year old to clean the refridgerator. Something will almost definetly get broken like the glass shelf, but luckily I had parts select which in no time assisted me to find the exact part. I ordered the part, it came quickly and I replaced within seconds.
Thanks.

took the cover off
(cardbord) the fan will come off and go back on by hand no tools needed i changed the fan motor just to be sure. 3 little screws hold it on. the plug only goes on one way u can't mess it up.very easy job u shouldn't have any problems doing it.Jim

No long shelf came with our new refrigerator, Frigdaire did not have one so I went on-line from you and it fit perfectly, now everything does not have to be in one big heap.

took out the broken, put in the new, lapsed time about 15 seconds. I keep looking in the fridge to enjoy how beautiful the new one looks.

Removed shelf from packing, washed it, slid it onto the refrigerator shelf rails and done. Took longer to unpack the shelf than install it! Very easy, perfect fit, and very happy with the exact replacement. Super careful packing, quick shipping. Very good experience. Hope I don't need anymore parts, but if I do, I will definitely get them here.

Removed replacement shelf from delivery box. Took items off of existing, broken shelf. Removed broken shelf. Slid new shelf into place. Placed items onto new shelf. Took the rest of the day off.

YOU TUBE VIDEO POINTED ME IN THE RIGHT DIRECTION. USED MULTI METER TO CHECK FOR VOLTAGE. NONE, REPLACED DEFROST HEATER. WORKS LIKE A CHARM, PART DELIVERED TO MY DOOR FOR LESS THAN $60.00, IN TWO DAYS FROM PARTSELECT. FIXED IT MYSELF FOR LESS THAN THE COST OF A SERVICE CALL.

Used model # of frigidaire on your web site... reviewed parts available... noticed shelves abailable... zoomed in to measure using crosshatch background... measured my freezer compartment... seemed doable... ordered shelf... receivednext day... attempted to slip in slots... had to grind off 3/16th inch on two legs... slipped in... Perfect!

I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.

Just removed the broken pan and installed the new one within 2 minutes. Really simple

I’m a technician,I was contacted by a customer. After listening to the customers issue I determine the freezer evaporator fan was bad. Real easy job loosen the hex head screws on top of the ice maker and pull it straight up. Disconnect ice maker wiring harness.remove the two top 1/4” screws that hold the back cover on and pull it forward. Disconnect your wiring harness and remove the whole back panel. Lay the back panel face down on the floor and remove two metal clips that are up at the top with a flat head screwdriver. Center plastic panel slides up and out maybe necessary to take a flat head screwdriver to the very top to release the plastic clip. Pull your fan blade off. On the backside of the motor just take and twist the flat plastic piece counterclockwise and remove your motor and install the new one Reassemble in the opposite order.

I slid out the old drawer and slid in the new drawer. Easy as that! I would recommend this website to anyone.

Perfect fit.