FRS22PRAD2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Arand from Yorktown, IN
- Parts Used:
- 5303288973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The original support was broken, tried epoxy and it only held for a few months before breaking again
All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Lake Luzerne, NY
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
first fresh food too hot, then freezer too hot
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from State College, PA
- Parts Used:
- 5303289501, 218147701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drawer and rails broke due to under design of the components
This was the second time i replaced the drawer and the first time for the frame.The repair was simply removing the old frame from the refrig and removing the rollers from the frame with screw driver. The rollers are reused with the new frame.The frame was reinstalled in the refrig.
The replacement of the drawer requires reusing the drawer front which is easily removable. The only complication with drawer repair was the need to trim some flashing that was not removed after the molding process at the factory to allow the drawer face to fit properly on the new drawer.
this problem is a quality control issue with the manufacture of the storage drawer.
The replacement of the drawer requires reusing the drawer front which is easily removable. The only complication with drawer repair was the need to trim some flashing that was not removed after the molding process at the factory to allow the drawer face to fit properly on the new drawer.
this problem is a quality control issue with the manufacture of the storage drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WETUMKA, OK
- Parts Used:
- 218147701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
storage drawer frame had cracked in the back
Simple, removed old frame, took off the humidity slide control and installed on new frame. Slid it back in place. Great service, had it the next day, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Grants, NM
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defrost timer was not working
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from ROADBURNS, TN
- Parts Used:
- 5303289500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Shelve pan broke on side
Removed old pan and cleaned all surfaces and reinstalled new pan.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WAYNE from NOVATO, CA
- Parts Used:
- 5303288973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The supports for the crisper cover had broken and the draws would not open correctly
I watch the how to repair video on line and the repair went very quick and easy.It was just like the video,no hidden suprises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Palmdale, CA
- Parts Used:
- 215314301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Right side door was grinding on the spindal.
We took the door off and replaced the pastic washer. Found out that the repair people never informed us that the door itself has a bit damaged so this repair would have to be done over and over. Nice way for them to make money off us.
We were able to fix it so that it will last a LONG time. Sometimes it realy can pay to do-it-yourself!
We were able to fix it so that it will last a LONG time. Sometimes it realy can pay to do-it-yourself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Watertown, WI
- Parts Used:
- 5303289500
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Slide ridges were cracked and broken
I used a small screwdriver to pry the tabs of the front glass panel loose, and then slid it upward and out of the broken storage drawer. Then I slid the panel into the front slots of the new drawer and pushed in an evenly downward manner until it snapped in place. It was an easy task and now we have a new drawer that slides smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bay City, MI
- Parts Used:
- 5304464438
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Fridge quit working.
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from SOUTH BEND, IN
- Parts Used:
- 5303289051
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light wouldn't turn on when door opened
Unplugged fridge, opened the door, used flat head screwdriver to pop off old switch, unplugged wires, plugged in new switch, popped it back in, and plugged the fridge back in. 2 minute fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jekaterina from ISSAQUAH, WA
- Parts Used:
- 5303289517, 5303289501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
NEVER GOT TO INSTALLATION POINT
Hello. Unfortunately, I never got to installation point. I got wrong item instead of the one ordered. I tried to return the wrong item but the label you provided was NOT PREPAID! It would cost me $57.50 to return this wrong item. I asked you to provide PREPAID RETURN LABEL but never got any answer to my request.
I got some of my money back for your mistake but I had to reorder my drawer and overpaid $10.94.
I still didn’t get the drawer I reordered… Installation? I wonder when it’s going to happen...
Thanks for asking anyway...
I got some of my money back for your mistake but I had to reorder my drawer and overpaid $10.94.
I still didn’t get the drawer I reordered… Installation? I wonder when it’s going to happen...
Thanks for asking anyway...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Sunnyvale, CA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No freezing or cold in either freezer or refridgerator - compressor did not run.
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Raleigh, NC
- Parts Used:
- 5303289500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer slides were cracked
The old drawer front needed to be carefully pried off with a plastic bladed screwdriver. The front simply slides onto the new drawer and is tapped into place with a rubber mallet.
Most impressive was the literally one-day standard (not overnight) delivery!
Most impressive was the literally one-day standard (not overnight) delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from Hickory, NC
- Parts Used:
- 5303289500, 218147701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Parts were Broken
Removed the broken drawer and Sfelf. Removed drawer front and attached it to new drawer part, Removed parts from shel fand reaattached to new shelf and installed both new parts. Couldn't have been any easier. Parts were great.
Was this instruction helpful to you?
Thank you for voting!