LGHT1837LE6 Frigidaire Refrigerator - Instructions

I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!

Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.

I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.

After removing meat tray the entire shelf including rails needs to come out. Once out a single set screw in the middle of rail needs to be removed. You can then slide the old rail across and then pull it out. Then insert new rail, slide across to lock in place. reinsert set screw. Don't over tighten. Be careful when replacing shelf as left side has air opening for drawer that must to match up.

Took off worn out rails and replaced with new ones using a Phillips screwdriver.

Removed two top trays, fixed the rail on the second tray by removing one screw and sliding out broken piece, and sliding in new arm and rescrewing. Screw was a little tight, but went in.Very impressed i was able to do it myself with your simple instructions.

1] Pulled the meat drawer out. 2] Removed the shelf holding the meat drawer. 3] Unscrewed the right side rail. 4] Installed the new rail and screwed in place. 5] Re- installed the shelf and meat drawer.

I just put the new one in with no problem

The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.

Pulled unit away from wall and shut off water and unplugged unit. Installed water valve and reassembled, plugged back in and turned on water and checked for leaks. All good. However there is no water getting into the ice maker. The unit itself is going thru a cycle of attempting to make ice and the bail is moving and you can hear the solenoid activate but no water. I have tried to blow thru the tube going to the maker but it seems to be plugged by something. I do not know if there is another valve up there or how to clean it out. Any help would be greatly appreciated.

Did get bulb from another company replaced bulb was told to hang on to the three bulbs for 30 days if they don't send return label in 30 days throw them out at 95 dollars each

Opened the box and slipped the new shelf over the existing brackets.Took approximately 1 minute. The shipping was very fast. Very happy with purchase.

Lifted old shelf out and snapped new shelf in. Took less than one minute to install. Identifying and ordering the correct part online was extremely easy due to the excellent presentation of the refrigerator and its parts. Ordered online one day and received the part the next day!

Had to replace both sides tracks; the plastic is thin and gets alot of use. Had these done in minutes, one screw out on each side allows the tracks to be removed.
Best part of the repair is the new clean shelves and drawers. How can you do this repair without cleaning everything?
Nice quick service from PartSelect, and the right parts!

Ordered the parts (slightly confusing as to which parts i needed since both the track and the spport rail had the same number) and after that arrived it took longer to empty the shelves than to install the parts, one screw on each side ( don't lose the screws because they do not come with the parts) to remove and replace. very easy and very quick.