FFTR2126LBE Frigidaire Refrigerator - Instructions

It was extremely easy. I opened door, unscrewed the two (2) screws at the top of the door handle with a phillips screw driver. Once screws were out I rotated the handle to the left and unhooked it from the mounting block. The new handle was already equipped with a mounting block. I attached the new handles mounting block to the door and rotated the handle up and positioned the holes to the holes on the door. I used the same 2 screws from the old handle and tightened them into the handle and door. That was it. Very easy.

Discovered the coil was covered with 1/2 inch of ice because defrost cycle had not been working. Replacing the defrost timer and melting ice with hair dryer fixed problem. Hooray!

Replaced thermostat and defrost timer and still freezer to warm.
After research with U-tube video of (Fixin it with Pappy) discovered that my fridge has one thermostat in fridge section and in cold months (live in ohio)the garage is cold therefore themostat in fridge does"nt need to tell the compressor to kick on. Pappy is a retired engineer and in very easy to follow instructions will show you how to fix this problem. Strongly suggest to search for his video on Utube. I did as he instructed and my fridge freezer works great in cold weather now. Its apparent to me I wasted my money on the parts. I didn't` need to replace. Just happy my Beer fridge is working all seasons now.
John from Ohio

You tube is my best friend for DIY repair. I supported the door with wood blocks, removed the bottom bracket and was able to slide the refrigerator door down and out without removing the freezer door. Replaced both hinge bearings and door stop and washer on bottom hinge and slid the door back into place. Door is very light when empty. Fast and easy, door opens and closes smoothly and no problem with condensation anymore.

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

I remove the old fan by pushing it off the spindle toward the evaporator and put the new one on by holding it on the right side and guiding it on the spindle from the left side, very easy task

Very simple. Remove the 2 top screws on the door, slide the lower part of the handel on to the lower screw on door .,swing the handle up to the top of he door and attach with the 2 original screws. DONE

I tied in to your web site orderd the parts the part were here in a day 1/2open cartons expecting to be broke but to my suprised they were in great shape and then fit perfectly the first time love your company.

The old gasket was dirty and old and it had ripped, so the fridge would no longer close. The new gasket came in and all we had to do was push it into the groves and make sure it was secure, and it was fixed. Saved me hundreds of dollars buying a new fridge.

Removed the old handle by taking the screw out at the top and sliding the bottom part off. Then slid the new handle on at the bottom replaced the screw at the top and done. Took less than 2minutes from opening the package to done.

Set new shelf in place and push down. Very easy!

I simply loosened the screws holding the refrigerator door handle and then slid the bottom portion of the handle off from the screw holding it in place. The bottom portion of the handle did not exactly marry-up with door, showing a very small gap. I attributed this to the age of the appliance.

Simple repair and less than 30 minutes.
But the video you had was taken down which showed you need to wind the timer. I called and was promptly sent another video, thanks Ashley !

Unfortunately the second video did not mention that you have to wind the timer, like the first video did. Turn clockwise till you hear 2 clicks.

All good. 20 year old fridge chugging along.

Easy replacement, I did add some glue to improve hold. The new handle design was a little different and did not match freezer door so I had to change both. I guess that's why they sell as pair.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.