FFHB2740PS2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Chuck from GRIFTON, NC
- Parts Used:
- 242220204
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water outlet tubing leaking in elbow behind water filter
Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Hampton, NH
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Previous seal had a tear and cold air was leaking around seal
Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Brookfield, CT
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator wasn't staying cool enough
Easily removed the old gasket and put the new ones on exactly the same way the old ones came off but in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lancaster, SC
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GASKET WORN AND LEAKING
SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND
THEN PUSHING THE NEW GASKET BY HAND
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andres from Golden Valley, MN
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced door gaskets with new ones
Removed the old door gaskets by hand and attached the new ones by inserting the edges in the existing grooves
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Oley, PA
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Thin, flexible edge on outermost door gasket was tearing from the main gasket, likely due to being rubbed when accessing refrigerator..
Gasket is held in place by an extrusion on the back side. Simply remove the old gasket and press the new gasket's extrusion into the track on the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from MAGNOLIA, AR
- Parts Used:
- 241675704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
ice maker is stuck on crushed ice.
We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Lockport, NY
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One blade broke from condenser fan
The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from OLATHE, KS
- Parts Used:
- 242009604
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Filter wouldn't engage
Basically unhooked water lines and removed the screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorena from HOQUIAM, WA
- Parts Used:
- 242071301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We had a broken bin on one of the doors.
We just slide in the bin.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Culver from RHINELANDER, WI
- Parts Used:
- 241894224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The little plastic bàlls came out of old part
Just took old one off and installed new. The company was great to work with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from CIRCLEVILLE, OH
- Parts Used:
- 241778811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flipper mullion assembly broke
Removed 1 screw and unplugged flipper mullion assembly and removed it. Plugged in new flipper and one screw and done. Works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from HURRICANE, WV
- Parts Used:
- 242093003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ice maker had stopped crushing ice although it still made cubed ice.
Took out the old ice container assemblyr and put in the new one. No installation was required. Just replaced it in the ice maker housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daune from OCALA, FL
- Parts Used:
- 241675704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice Maker was making ice erratically
After sending PartSelect the info to their troubleshooting dept. about my ice maker, they recommended replacing the ice solenoid. I did so at a cost of $102. No change, turned out replacing the ice maker(did not purchase from PartsSelect) was the issue and works fine now.
So wasted $102. FYI the part took 6 days to arrive.
So wasted $102. FYI the part took 6 days to arrive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Warrensburg, MO
- Parts Used:
- ULTRAWF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
time to change water filter
first, there many different water filters. your experience will be different according to your water filter type.
Was this instruction helpful to you?
Thank you for voting!