FFHS2311LBPA Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Melissa from Olden, TX
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker was producing hollow ice due to water was free flowing out the water dispenser during fill time for icemaker.
Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Marco Island, FL
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker was over filling.
Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SEATTLE, WA
- Parts Used:
- 242009604
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water filter would not disconnect from OEM Water Filter Base
Disconnect the two water supply tubes at the base of the Water Filter Base. Using a 7/16" open end wrench, press up on the blue "O" rings to disconnect the tubes. Use a Using an 8" long magnetic phillips head screw driver I was able to unscrew the 4 short screws holding the original water filter base and the immovable attached water filter. Replacement was easy. Simply slide the new base into the fixed slot on the refrigerator and reinstall the 4 holding screws. Reconnect the water supply tubes to the Water Filter Base. Install a new water filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Kenosha, WI
- Parts Used:
- 240363701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken refrig door shelt bin
Put on new shelf in seconds. What a wonderful way to be able to purchase the perfect part easily through the internet. I ordered the part on Sunday and received it on Tuesday. THANK YOU Parts Select!!! K.F.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarence from Oakland, CA
- Parts Used:
- 240363701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had a broken door shelf
It was very easy to insert the new shelf door into the refrigerator slots.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from SODUS POINT, NY
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
No water to ice maker
Repair was easy. Unplug refrigerator, turn off water to ice maker, remove back panel, disconnect water inlet valve, disconnect water supplies and electrical connections. Cut ends off tubing to modify to new part connections, connect tubing, connect electrical supplies, reinstall back panel, plug refrigerator in, turn water supply back on. We made sure that there was no ice build up in the supply tube into the ice maker and made sure that everything worked correctly before putting it all back together. It was an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eugene from BROOKLYN, NY
- Parts Used:
- 240354602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Easy
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVE from CRESTON, IA
- Parts Used:
- 241684503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice maker would not dischare ice
Followed the online video from this site
Was this instruction helpful to you?
Thank you for voting!
Doesn't make ice / doesn't dispense ice
Removed and replace solenoid manifold valve in rear of appliance using inadequate You Tube video. Removed and replaced augur motor after dismantling various housings using a seriously mistaken You Tube video. The latter video informed us that the yoke that screwed on the motor's shaft was a reversed Left Hand thread. It wasn't at all, and we struggled to figure that out. The people that make these videos leave out steps that they thunk are obvious, but aren't at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Jim Thorpe, PA
- Parts Used:
- 241682003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Lever to dispense water broke off
Unplug refrigerator first. Remove 4 screws on front and lift off cover. Unplug unit small plug with around 6 wire on it on the top. Unscrew inside scres that hold the lever in place. Put the new one in slots and put in screws to hold in slot. Put cover back on. Make sure ice dispenser is still working seemed to disengage the unit during the repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shawn from CORTEZ, CO
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice crusher selection door broken
Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ELK GROVE, CA
- Parts Used:
- 242009604
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
New off brand water filter could not be removed from the water filter base
Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from THE PLAINS, OH
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dispenser Crusher Housing was broken
I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from LIVERMORE, CA
- Parts Used:
- 241885001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The ice crushing housing was broken.
The repair went easily after watching the video, took me less than an hour to complete the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Ravenswood, WV
- Parts Used:
- 241850615
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Not making ice
Took out old replaced with new. Now it makes ice
Was this instruction helpful to you?
Thank you for voting!