FFHS2311PFHA Frigidaire Refrigerator - Instructions

Fridge has Ice & water in Door.
Slide bottom plate out.Remove three screws
across bottom.
Remove two screws that holds a circut board.
pull the water hose off and remove board.The hose is a little tricky getting back on.

remove two screws that holds two little plates and remove old part.
Reverse prosedure to put back.

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

I followed the video tutorial published here. The step I altered was setting the shrink wrap; I did not have a heat gun to safely shrink it, so I folded it tightly onto itself and wrapped it in electrical tape. No more frost buildup.

Watched repair video on plastic auger repair and decided to just invest in the whole replacement unit. 45 minute vs. a 5 minute repair.....no brainer. Removed shipping materials from new dispenser, placed on counter top. Removed old ice dispenser, dumped existing ice into new dispenser. Installed new dispenser with ice back into freezer. Tested and unit now dispenses ice.. Easiest fix I've done to date.

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

Remove power from refrigerator. Pull out the drip tray below paddle. Removed the 3 screws behind tray. Gently pull control panel out and remove the ribbon cable plug from panel. Set panel aside. Remove three screws holding panel housing to door, then pull out housing slightly and disconnect harness plug behind left side of housing. Pull housing out 3-4 inches. Look at the way paddle tabs engage ice dispenser switch mechanism. Remove the left paddle hinge screw and plate and loosen the right hinge screws(these also hold the water paddle hinge) Remove broken paddle by pulling out from right hinge plate and down. Install new paddle under right hinge plate, engage new paddle tabs correctly onto dispenser switch, install left hinge plate and screw, then tighten hinge screws. Reconnect harness plug, reinstall 3 housing to door screws, reconnect ribbon plug to control panel and reinstall panel screws. Reinstall drip tray. Reconnect power to refrigerator and check operation of ice and water paddles.

Twisted replacement bulb into place easily. Let there be light!

Slid the shelf in place!

very easy to do. just snap into place

Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

I removed the ice container found the part # on the bottom ordered a new one and installed it. It just slipped right in to place.

Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

The repair was easy. It just required a little time and patience. There are about a half dozen screws to remove and three of them are very small. I woild suggest a phillips head screwdriver with a magnetic tip for the small screws. They can easly fall into the control unit and be hidden. If they happen to fall, a small pen-type magnet that is expandable will make it easy to retrieve. I used a small set of needle-nose pliers to replace the small metal plates over the plastic pins that hold the water actuator in place. If your are careful, this repair can be done without disconnecting any of the electrical wiring.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Looked at video on how to remove and reinstall support and followed the instruct ions