FFHS2313LE5 Frigidaire Refrigerator - Instructions

Replaced part and slid into place.

There was no repair needed. I broke the glass shelf that inserts to a plastic frame that holds the fruit/veggie drawer on the fridge.

I found the part very easily on the site and ordered it. The part came exactly as described on the Web site.

The part arrived in about 2 days! The right side support that is attached to the inside wall of the refridgerator, that holds the crisper guide, broke apart and would not support the crisper. We took everything off of that shelf and took out the crisper and the glass that is on the shelf. We then carefully pried the support from the interior wall (it was a slow tedious move to be sure we did not damage the wall of the fridge). We made sure all of the pieces were out and snapped the new one into place. For some reason the old one did not want to come out. It broke into many pieces and we carefully pulled all of the little pieces out of the notches

i ordered a replacement, and when it came in i took the old part off and installed the new dispenser. it works great.

after changing all the pieces the evaporator continues to freeze and stops cooling

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23

Wasn't sure what parts to replace so happy to find intact entire assembly. Popped out the old, popped in the new. Back in business in less than 5 mins. Highly recommend.

1. Using Philips head screwdriver, remove plastic hinge cover on top of refrigerator door.
2. Remove bolts using socket wrench.
3. Lift door from bottom hinge.
4. With Philips head screwdriver remove screw holding bearing in place on bottom of door.
5. Remove old bearing.
6. Install new bearing.
7. Replace fridge door using reverse steps.
8. Enjoy your handi-work.

Took out the out one and slid in the new one so easy to do

Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.

Removed old ice maker , emptied ice into new ice maker and installed ice maker, it took less then 2 minutes to complete job and no tools needed , this was the easiest repair I have ever done.

New part fit nicely in an instant. Only issue is that it is a white replacement part and ours was clear...not a big deal because this is the bottom drawer so you really don't even notice.

This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.

Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!