FFHI1826LBB Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from Andover, CT
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Refrigerator door was not sealing correctly.
Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- José from ORLANDO, FL
- Parts Used:
- 242044008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Fridge was cooling down enough the heating defrost was bad
I take 2 crew on front of the fridge take the cover and fan out replaced the part and put everything back it’s a easy job thanks guys for the parts from Orlando fl
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SAN FRANCISCO, CA
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Accidentally broke the glass insert.
Simply slide the new glass insert in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from SOUTHFIELD, MI
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken glass on top of crispers
Since the glass was broken and gone I just had to slide the new glass on top of the crispers. This was not really a repair, just an exchange of new for the old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RALPH from PARIS, KY
- Parts Used:
- 240358926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Shelf was broken
Slid the old shelf out. Attached meat drawer to new shelf and slid it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from FORT MYERS, FL
- Parts Used:
- 5304506471
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The handle on the refrigerator broke at the top
Removed the old handle by taking the screw out at the top and sliding the bottom part off. Then slid the new handle on at the bottom replaced the screw at the top and done. Took less than 2minutes from opening the package to done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from KNOXVILLE, TN
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker would dump ice one time and then stop. Turning the ice maker off for a minute and back on would repeat the process.
I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from WALLING, TN
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from POTTSTOWN, PA
- Parts Used:
- 240358926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Just replaced the old broken one
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GROTON, CT
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working. Part needed to repair it no longer available so had to replace the whole icemaker.
Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from FRANKLIN, NY
- Parts Used:
- 240358926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old shelf was broken.
Remove the old shelf. Slide in the new shelf and add the meat draw underneath. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Cleveland Heights, OH
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace shelf
I can't believe I put if off so long... so easy to do and PartSelect was very fast, efficient, and the cheapest vendor for my part.
Was this instruction helpful to you?
Thank you for voting!
both shelfs broke after jar slipped
removed both the shelf retainer and shelf bin, replace with the new units ordered from partselet.com. the whole process from searching, ordering, shipping and installing was very easy... thanks for everything
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Poland, IN
- Parts Used:
- 240358926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf and edging broke
The shelf fit perfectly. No problems. Was very pleased with the product.
Was this instruction helpful to you?
Thank you for voting!