FGHC2355PF9A Frigidaire Refrigerator - Instructions

1. Using Philips head screwdriver, remove plastic hinge cover on top of refrigerator door.
2. Remove bolts using socket wrench.
3. Lift door from bottom hinge.
4. With Philips head screwdriver remove screw holding bearing in place on bottom of door.
5. Remove old bearing.
6. Install new bearing.
7. Replace fridge door using reverse steps.
8. Enjoy your handi-work.

Removed two screws and disposed of two broken tabs holding old trim in place. Placed new trim in place, fastened the same two screws. Done.

About two minutes.

Very simple less then five minutes.

Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test

Took the part out of the box and slid it in to place. It fit perfectly!

Original unit had screw on lugs. After removing old unit, I unscrewed the lugs, cut the lines to remove the nuts and inserted them into the new unit. Everything was color coded so connection was simple. Reinstalled unit, cycled the ice maker several times only to discover the fill tube at in the freezer had frozen ice blocking the tray from getting water. Used a hair dryer to thaw out the tube, water flowed instantly. Very easy repair.

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

Removed and replace solenoid manifold valve in rear of appliance using inadequate You Tube video. Removed and replaced augur motor after dismantling various housings using a seriously mistaken You Tube video. The latter video informed us that the yoke that screwed on the motor's shaft was a reversed Left Hand thread. It wasn't at all, and we struggled to figure that out. The people that make these videos leave out steps that they thunk are obvious, but aren't at all.

Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

The repair went easily after watching the video, took me less than an hour to complete the repair.

Can't supply any info that would be helpful. Ordered a " badge" that covered 100% of the scratch and stuck it on. Scratch now covered and problem solved. Thanks for asking.

I changed the defrost thermostat and the heater.

I TOOK A PICTURE OF THE LABEL INSIDE THE DIVICE SO I DID NOT NEED OT REMEMBER IT WHILE GOING TO MY COMPUTER TO LOOK UP THE PART. I FOUND PARTSELECT AND ORDERED THE PART. I GOT GOOD EMAIL COMUNICATION FROM PARTSELECT ABOUT THE ORDER AND EXPECTED DELIVERY. I DONOT REMEMBER IF THEY KEPT THEIR WORD BUT THE PART CAME IN SOON ENOUGH. WHEN IT ARIVED I GOT MY BOX KNIFE AND CUT THE BOX OPEN TOOK OUT THE DRAWER AND SLIDE IT INTO THE SPOT WERE THE BROKEN DRAWER WAS. I DID CLEAN THE SPACE WHERE THE OLD DRAWER WAS IT WAS EMBARRISING DIRTY. I WOULD RATHER NOT TALK ABOUT THAT BUT IF YOU LIKE I CAN SEND PICTURES. THE DOOR IS WORKING FINE JUST LIKE THE ORIGINAL ONE DID. PARTSELECT WAS A GREAT CHOICE IT WAS QUICK AND EASY. IF YOU DONT USE PARTSELECT YOU ARE GOING TO JUST MAKE YOUR REPAIR HARD ON YOURSELF.