FFHS2313LP5 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack from WALLING, TN
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eugene from BROOKLYN, NY
- Parts Used:
- 240354602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Easy
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVE from CRESTON, IA
- Parts Used:
- 241684503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice maker would not dischare ice
Followed the online video from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Gautier, MS
- Parts Used:
- 242044113, 5303918214
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer not defrosting creating ice buildup at evaporator fan
Removed evaporator cover and dismounted evaporator coil. Threading in the new heater was difficult but not impossible.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BEVERLY from CHICAGO, IL
- Parts Used:
- WF3CB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problem on the installation.
I just follow the instructions , it was really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from BAXLEY, GA
- Parts Used:
- 241860803
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Feed wheel broke and ordered the whole assembly working fine so far
Took out the out one and slid in the new one so easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacey from THE WOODLANDS, TX
- Parts Used:
- 241860803
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Stopped crushing ice.
Wasn't sure what parts to replace so happy to find intact entire assembly. Popped out the old, popped in the new. Back in business in less than 5 mins. Highly recommend.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from ROGERS, AR
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Freezer was cooling, but refrigerator was not cooling all the time. Evaporator fan was running, so decided to try new thermostat.
Followed install instructions on utube. Once freezer was empty, back panel was easily removed, and defrost thermostat was in plain sight, and easy to replace. Hope that solved my problem. Refrigerator has been plugged in for four days now, and is cooling properly so far.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cloid from HOOVER, AL
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice Director Door Broken In Half
I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Berthoud, CO
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Part broke though normal use
Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from LIVERMORE, CA
- Parts Used:
- 241885001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The ice crushing housing was broken.
The repair went easily after watching the video, took me less than an hour to complete the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robinson Ruiz from Miami, FL
- Parts Used:
- 241600906, 242135301, 241563601, 5303918214, 215474201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench set
it doest not cool
after changing all the pieces the evaporator continues to freeze and stops cooling
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from SEBRING, FL
- Parts Used:
- 241688401
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Part 30 on the Ice and water dispenser drawing was broken and needed to be replaced in order to seal the ice chute opening into the freezer.
Followed the video for this repair. Only issue was that the videos showed that when the front panel is removed, there is a wire harness that has to be unplugged from part No. 38c. This was not the case. What I had was a Ribbon Cable Harness that plugged into the front of part No. 38 and the top of part 38C (the two power boards) I tried to disconnect it from part 38C by pulling it out, and apparently damaged the Ribbon Cable Harness. Later found a video showing how to remove this item properly when replacing power boards 38 and 38C. Have ordered a new cable from GRP and hopefully this will solve the problem, as there is no electrical current to the dispenser controls and the ice and water dispenser are not currently working. Would have been nice to know that there are two types of connections between these power boards; a cable harness that unplugs from 38C or a Ribbon Cable Harness that unplugs from from the face of part No. 38. Hopefully I have not damaged either of the boards or anything else. Professional repair man coming on Thursday to test the boards, micro switches, etc. The boards are quite pricey, ($550.00 for both) and since the refrigerator was manufactured in 2004, we will buy a new one before we pump any more into this older unit. Very important to know how to unplug this Ribbon Cable Harness from the boards before proceeding ! Plug in on 38C is very tricky and you will need to review a video showing how it is done.
Was this instruction helpful to you?
Thank you for voting!
Ice Crusher Houseing cracked broke into pieces
Remove ice drawer ,Removed front of drawer 4 screws ,Removed broken crusher 3 screws Ordered new parts reassembled replaced fix blade spacer that was broken and blade cover housing reattached front of drawer !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Ravenswood, WV
- Parts Used:
- 241850615
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Not making ice
Took out old replaced with new. Now it makes ice
Was this instruction helpful to you?
Thank you for voting!